View Policies Current Attempt in Progress (Laminar flow) A fluid flows through two horizontal pipes of equal length which are connected together to form a pipe of length 21. The flow is laminar and fully developed. The pressure drop for the first pipe is 1.678 times greater than it is for the second pipe. If the diameter of the first pipe is D, determine the diameter of the second pipe. D3 = Save for Later D Attempts: 0 of 3 used Submit Answer

View Policies Current Attempt in Progress (Laminar flow) A fluid flows through two horizontal pipes of equal length which are connected together to form a pipe of length 21. The flow is laminar and fully developed. The pressure drop for the first pipe is 1.678 times greater than it is for the second pipe. If the diameter of the first pipe is D, determine the diameter of the second pipe. D3 = Save for Later D Attempts: 0 of 3 used Submit Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
Problem 4. The open tank shown in the figure have 2 piezometers attached on one side, containing two different liquids, A (SG=0.83) and B (SG=2.50). Find the (.- El 5m a. elevation of liquid surface in piezometer B b. total pressure at the bottom of the tank. Liquid A El Im Liquid B El Om
Water in the reservoir is used to control the water pressure in the pipe at A. Take pHg = 13550 kg/m³ and p = 1000 kg/m³ Neglect the diameter of the pipe. (Eigure 1) Figure AQ B E h 400 mm C 150 mm 100 mm 200 mm Mercury pe he Y Part A If h= 140 mm, determine the gage pressure in the pipe at A when the mercury is at the elevation shown. Express your answer to three significant figures and include the appropriate units. PA 76.8 Submit 4 Provide Feedback kPa CINC Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining
Given a three-pipe system, the total pressure drop is P,- P, 150,000 Pa, and the elevation drop is Z, - Z, = 5 m. The pipe A data are: Pipe L, m d, cm E, mm eld 1 100 8 0.24 0.003 2 150 0.12 0.002 3 80 4 0.20 0.005 The fluid is water (density 1000 kg/m' and kinematic viscosity 1.02x10 m/s). Calculate the flow rate Q in m'/h through the system. 3
Q2. A 200 mm x 100 mm venturimeter is provided in a vertical pipeline carrying oil of S = 0.9. The flow is in the upward direction. The throat is above the inlet by 0.25 and the differential manometer shows a gauge deflection of 0.25 m of Hg. Determine, (a) Discharge of oil (b) The pressure difference in N/m^2 between * entrance and throat by using basic Bernoulli's equation. Take Cd = 0.98
Q1) Given is a three-pipe series system, as in Fig. 150,000 Pa, and the elevation drop is ZA - ZB = 5 m. The pipe data are The total pressure drop is pa - PB = Pipe L, m d, cm €, mm eld 1 100 8 0.24 0.003 2 150 6. 0.12 0.002 3 80 4 0.20 0.005 The fluid is water, p 1000 kg/m and v = 1.02 x 10-6 m/s. Calculate the flow rate Q in m/h through the system. (3 (2 A B
1- Water flows through a horizontal pipe at a rate of 9.1 L/s. The pipe consists of two sections of diameters 10.16 cm and 5.08 cm with a smooth reducing section. The pressure difference between the two pipe sections is measured by a mercury manometer. Neglecting frictional effects, (a) determine the differential height of mercury between the two pipe sections. (b) How would the reading change if the manometer on the 2in pipe is replaced by a pitot tube? 10.16 5.08 h
Water flows from a to e through the pipe system shown in the figure. It is known that the flow in pipe bfgc is 50 liters per sec. (a) Assuming that C1 = 120 for all the pipes, determine the total flow from a to e. (b) Assuming that all the pipes are level and that the pressure head at a is 80 m, determine the pressure head at point d.
The pressure at point 2 shown in Figure is not to fall below 4.14 Bar when the flowrate from the tank is 0.028 m^3/ sec. Determine the minimum height, h, of the water tank under the assumption that (a) minor losses are negligible, (b) minor losses are not negligible. 3 m Figure No.3 Kentrance = 0.5 h The pipe is plastic of 15 cm diameter and (e/D=D0) 1.8 m (2) Main line 450 m with 15 elbows of 90 degree
3. What is the pressure difference between pipe A and pipe B? Give pressure difference in kPa. (y = 1.22 m and h 30 in.) The gage fluid, M, is mercury with a specific gravity of 13.54 State assumed values if any. Water A Water B y D Liquid M
A fluid is flowing in a pipe 20-cm∅ with a mean velocity of 3 m/s. The pressure at the center of the is 35 kPa and the elevation of the pipe above the assumed datum is 5 m. compute the total head, E in meters, if the fluid is:a) Oil (sp.gr. = 0.85)b) Gas (γ = 6.30 N/m3) c) Water Pls include figure for better understanding
Given The figure shows an inlet and outlet connected to a motor. If the pressure at A is 6.25 MPa and the pressure at B is 3.15 MPa. The motor inlet is a steel hydraulic tube with 25 mm OD × 1.5 mm wall and the outlet is a tube with 50 mm OD × 2.0 mm wall. The fluid is oil (sg = 0.84) and the velocity of flow is 1.40 m/s at point B. h1 = 2.60 m Required Calculate the power delivered to the hydraulic motor in kW to the nearest 100th. A h1 Flow |Motor