VHF loop antenna used to receive weather maps from satellites has an mpedance of 10002 at 137MHz. This antenna will be used with a receiver whose input impedance is 50 ohms, by using figure 3: What is the impedance of the quarter wave matching section? What is the length of the matching section cable which has a relative dielectric constant (,) equal to 1.77? LOOP ANTENNA Z-100 22 Receiver Z-5052 QUARTER WAVE SECTION

VHF loop antenna used to receive weather maps from satellites has an mpedance of 10002 at 137MHz. This antenna will be used with a receiver whose input impedance is 50 ohms, by using figure 3: What is the impedance of the quarter wave matching section? What is the length of the matching section cable which has a relative dielectric constant (,) equal to 1.77? LOOP ANTENNA Z-100 22 Receiver Z-5052 QUARTER WAVE SECTION

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3) Solve the cutoff frequency for the first mode and second mode of WR975 Wave guide TABLE 7.1 Some Standard Rectangular Waveguides Waveguide de signation a (in) b (in) t (in) fe, (GHz) Frequency range (GHz) WR975 9.750 4.875 0.125 0.605 0.75-1.12 WR650 6.500 3.250 0.080 0.908 1.12–1.70 WR430 4.300 2.150 0.080 1.375 1.70-2.60 WR284 2.840 1.340 0.080 2.08 2.60-3.95 WR187 1.872 0.872 0.064 3.16 3.95-5.85 WR137 1.372 0.622 0.064 4.29 5.85-8.20 WR90 0.900 0.450 0.050 6.56 8.2–12.4 WR62 0.622 0.311 0.040 9.49 12.4–18
What does the TE mean? Why does one have a 10 as subscript and the other mn? What is a broad and short dimension and a rectangular waveguide?
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface. For the interface, I'm a little confused. I used a voltage divider and got V_transmitted = 0.8 and V_incident = 1.2. But shouldn't they be the same?
What are the types of power loss in a rectangular waveguide?
Sketch/Draw the following: a. 100% modulation trapezoidal pattern b. Negative Carrier Shift c. Envelope of a square wave modulating a sinusoidal carrier
This subject is antenna and wave propagation of ece pls solve neatly and faster thanks
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface.
What is a waveguide? What is a slab waveguide? What is a planar waveguide? What is thin slab?
A 10 MHz carrier is frequency modulated by a sinusoidal signal of 500 Hz frequency and the maximum frequency deviation is 50 KHz. What will be the bandwidth of the FM signal?
A sinusoidal wave m(t) = 15csin2500nt, is applied to an FM generator that has a frequency modulation constant of 50 Hz/volt. Determine the frequency deviation and modulating index.
3) Solve the cutoff frequency for the first mode and third mode of WR137 waveguide. TABLE 7.1 Some Standard Rectangular Waveguides Waveguide designation a (in) b (in) t (in) Seo (GHz) Frequency range (GHz) WR975 9.750 4.875 0.125 0.605 0.75-1.12 WR650 6.500 3.250 0.080 0.908 1.12-1.70 WR430 4.300 2.150 0.080 1.375 1.70-2.60 WR284 2.840 1.340 0.080 2.08 2.60-3.95 WR187 1.872 0.872 0.064 3.16 3.95-5.85 WR137 1.372 0.622 0.064 4.29 5.85-8.20 WR90 0.900 0.450 0.050 6.56 8.2-12.4 WR62 0.622 0.311 0.040 9.49 12.4-18
How can ground wave coverage be increased?