Solution Please Use the figure below. A coil with four (4) turns is wound around a closed core with cross-sectionalarea of 30cm², relative permeability of 1200, and a mean path length of 50 cm. A magnetic sensormodule of negligible thickness is installed within the core; this module has a transfer equationV1=50+0.2, where is the flux in Wb and V1 is in volts. Neglect fringing and saturation effects.CorefluxФsensor+V₁Ax + B+V₂1. Find the sensor output voltage V1 when 60 A DC is passing through the input coil. Expressyour answer in mV up to 3 decimal places.2. Find the constant A and B such that a 1 A DC input will yield V2=10mV while a 400 A DCinput will yield V2=10V. Give your answer up to 3 decimal places.3.A 500-A 50-Hz sinusoidal current is passing through the input coil. Find the reactive powerconsumed, in kVAR up to 3 decimal places.

Answered: Image /qna-images/answer/f212f174-2283-4d88-b23a-2b4cb8164bc6.jpg

Use the figure below. A coil with four (4) turns is wound around a closed core with cross-sectional area of 30cm², relative permeability of 1200, and a mean path length of 50 cm. A magnetic sensor module of negligible thickness is installed within the core; this module has a transfer equation V1=50+0.2, where is the flux in Wb and V1 is in volts. Neglect fringing and saturation effects. - Core flux $ sensor + V₁ - + Ax + B V₂ 1. Find the sensor output voltage V1 when 60 A DC is passing through the input coil. Express your answer in mV up to 3 decimal places. 2. Find the constant A and B such that a 1 A DC input will yield V2=10mV while a 400 A DC input will yield V2=10V. Give your answer up to 3 decimal places. 3. A 500-A 50-Hz sinusoidal current is passing through the input coil. Find the reactive power consumed, in kVAR up to 3 decimal places.

Use the figure below. A coil with four (4) turns is wound around a closed core with cross-sectional area of 30cm², relative permeability of 1200, and a mean path length of 50 cm. A magnetic sensor module of negligible thickness is installed within the core; this module has a transfer equation V1=50+0.2, where is the flux in Wb and V1 is in volts. Neglect fringing and saturation effects. - Core flux $ sensor + V₁ - + Ax + B V₂ 1. Find the sensor output voltage V1 when 60 A DC is passing through the input coil. Express your answer in mV up to 3 decimal places. 2. Find the constant A and B such that a 1 A DC input will yield V2=10mV while a 400 A DC input will yield V2=10V. Give your answer up to 3 decimal places. 3. A 500-A 50-Hz sinusoidal current is passing through the input coil. Find the reactive power consumed, in kVAR up to 3 decimal places.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please choose the correct answer and explain if possible. Thank you. 4. The main terminal voltage across an ON conducting SCR depends on the instantaneous main terminal current in the following way: a. They are proportional b. The voltage increases as the current increases, but no quite proportionally c. The voltage increases as the current increases, by a squared (seond power) relationship d. They are virtually non-related 5. To turn Off a conducting SCR in a dc-powered circuit, it is necessary to: a. Interrupt (stop) the gate current b. Wait for the main terminal current to fall below IHO when the supply voltage crosses through zero c. Deliver a pulse of negative gate current via the gate lead d. Place a temporary reverse bias across the SCR’s main terminals 6. In a simple RC charging circuit used for trigger-control of an SCR, a good range of adjustment of the RC time-constant is: a. 1 to 5 msec b. 1 to 30 msec c. 0.1 to 10 msec d. 2 to 25 μsec
Consider a ferromagnetic ring (nucleus) that has a mean circumference of 40 cm, 300coiled copper turns and a sectional area of 5 cm2. A current of 2 is appliedA to winding, producing a flux of 1.5 mWb.Determine the permeability of the core material.Determine the relative permeability of the core material.If the ferromagnetic ring has an air gap of 2 mm. Find the required MMFso that the flux density in the gap is 0.5 T.
A magnetic circuit consists of silicon steel of 3000 permeability, of 10 cm length and a 2 cm air gap. Both have the same cross section of 1.5 cm2. A current of 0.5 flows through the 5000 turn coil. Find the field intensity at the air gap in Oersted.
An air-gap between two pole pieces is 20 mm in length and the area of the flux path across the gap is 5 cm². If the flux required in the air-gap is 0.75 mWb find the m.m.f. necessary.
A triac can pass a portion of …………… half-cycle through the load a. neither positive nor negative b. both positive and negative c. only negative d. only positive
The saturation curve of a particular core material shows that at a magnetic field intensity of 1250 At/m and the flux density is 0.80 Tesla. Determine the relative permeability of the core material.
Discuss the salient features of BCS theory for superconductors.
Identify the following: 1. This refers to the regions of magnetic alignment. 2. This phenomenon is exhibited by superconductors where magnetic field is expelled under critical temperature 3. Produced due to the direct recombination of electrons and holes.
A. A coil of 1000 turns is uniformly wound on a ring of non-magnetic material, the mean diameter being 20 cm. The cross-sectional area of the coil is 4 cm2. Determine the selfinductance of the coil. Ans. 0.8mH B.An iron core 0.4m long and 5 cm2. In cross section, is wound with 300 turns. When a current of 0.5 A flows in the coil, how much is the inductance of the coil. Assume the core has a permeability of 2500.
Describe what coupling capacitors are and what are they for?
2. AC-core with a gap of 0.0001m has a coil number of 100 and a current of 10mA. First find the Reluctance of the core given that the Iron core has a negligible reluctance and only the air reluctance contributes to the majority of reluctance. The core has a cross sectional area of 2cm^2. Next find the flux flowing thru the C-core.
Determine the transfer function for a tubular heat exchanger similar to the one shown in Figure 2.3 and described by the following differential equation: ** Please see attachment