Problem: In ASTM D198 where it determines the flexure properties of wood such as modulus of rupture, modulus of elasticity, and failure conditions, determine the types of failure shown in each wood. Question 15 Use the editor to format your answer

Q: 2.) A 9-m simple beam is carrying a uniform load of 25 kN/m over the entire beam with two-point…

A:

Q: The cantikver frass is loaded. Determ ine the reacthon at E. 3 5 m OD KN 20 KN

A:

Q: A triaxial shear test on saturdated soil has the following  results: Determine: a. Drained angle of…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 90 MPa and S, =…

A: Given data in question  Normal stresses as compressive and tensile  Angle No shearing stress To find…

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

A: To find maximum deflection and it's location

Q: The extruded plastic shape has dimensions of D= 38 mm, d= 36 mm, a = 80 mm, and t= 4 mm. (a)…

A:

Q: For the beam and loading shown, use discontinuity functions to compute: (a) the deflection VA of the…

A:

Q: Three main STEEL making processes. Briefly describe each process.

A: The three major steelmaking processes are: Basic oxygen Open hearth and Electric arc

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b = 5.6 in., d = 5.0…

A:

Q: A WT305 x41 standard steel shape is used to support the loads shown. Assume W= 50 kN/m, LAB = 1.1 m.…

A: To Determine Maximum Compressive and tensile stress.

Q: The motor is towing the crate that has a mass of m. = 1000 kg, and rests on the flat surface. It…

A:

Q: Given the following data of a doubly-reinforced rectangular beam. Beam width, b=410mm 20 mm Overall…

A:

Q: [Soil Bearing Capacity] Assume the general shear failure and use a factor of safety 2.8. Determine…

A: Given data, bearing capacity factors, Nc = 25.13  Nq = 12.72 Nγ= 8.34 Diameter of footing, D = 3m…

Q: Determine the vertical reaction (in kN) at the support C of the given beam using Method of…

A: Given data in question  Load P Span member length  To find out  Reaction C

Q: 4. [Shear Strength] ( ) A triaxial shear test on saturdated soil has the following results: Cell…

A:

Q: An open cylindrical tank having a radius of 300mm and a height of 1.2m is full of   water. How fast…

A:

Q: occupational health hazards

A: The classification of Occupational health hazards include: Environmental Hazards  Chemical Hazards…

Q: 2. Determine the reactions at 'B' and 'D' 20 kN 6 m 2 m 4 m 3 m 12

A:

Q: Q8 Which of the following requires an LRFD strength reduction factor of 0.9 for overall member…

A:

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

A:

Q: Pc WAB D. B Lạc by di b3

A:

Q: The strain components &x, Ey, and yxy are given for a point in a body subjected to plane strain.…

A: Mohr's circle  The transformation equations for plane stress problems are shown graphically by…

Q: Current Attempt in Progress AWT305 x 41 standard steel shape is used to support the loads shown.…

A:

Q: A laminated wood beam consists of eight 1.75 in. x 5.50-in. planks glued together to form a section…

A: To find out the moment of inertia about Z axis.

Q: Given in the tabulation below are the observed forward and backward bearings of an open compass…

A:

Q: AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 56 kN/m, LAB = 1.0…

A: To Determine Maximum Compressive and tensile stress.

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.5 in., b = 5.4 in., d = 4.9…

A:

Q: own. Assume L1 = 0.8 m, L2 = 1.6m, P = 5 kN, Q = 34 kN, a = 135 mm, b = 130 mm, c = 80 mm, and d =…

A:

Q: The wood beam supports loads of w = 420 lb/ft and P = 820 lb on span lengths of LaB = 8.2 ft, Lgc =…

A:

Q: Solve the given truss. 50 kN 60 kN 2 m F E 2 m 2 m K 2 m L 2 m M A 4 m Determine the following: 6.…

A: All parts are being solved

Q: 1.) A standard HS truck is moving across a 25-m simple span. The wheel loads are Pa= 36 kN, Pb = 142…

A: Given data: Span = 25 m

Q: For the cantilever steel beam [E = 190 GPa; I = 90 x 10ʻ mm“], use the double-integration method to…

A:

Q: A composite beam made of steel and bronze has the cross section shown. The cross-sectional…

A: Calculate the magnitude of the allowable bending moment that can be applied about the z centroidal…

Q: For the beam and loading shown, use discontinuity functions to compute: (a) the deflection VẠ of the…

A: Given  LAB= 1.7m ,LBC=3.3 m

Q: x 360 mm rectangular beam as shown in the figure. 100 kN/m 20 50 kN/m 1.5 m 5 m ne maximum value of…

A:

Q: (a) the maximum horizontal shear stress in the beam. (b) the maximum tensile bending stress in the…

A: Bending stress: -It is stress that is induced to resist bending moments of beam.

Q: At a point in a stressed body, the known stresses are o, = 16 ksi (T), oy 11 ksi (T), o, = 12 ksi…

A:

Q: 15 kN 15 kN 25 kN/m A B C E 1.5 m E1.5 m→

A:

Q: Example: Determine the nominal eccentric compressive strength P, and the cccentricity e…

A:

Q: Homework: (Column Strength Interaction Diagram ) Assume equal rebar at four sides Check if a column…

A:

Q: Tourists arrive at the Manila Zoo at a rate of 250 vehicles per hour. But before entering the zoo,…

A:

Q: A cantilever timber beam with a span of L- 3.7 m supports a uniformly distributed load w. The beam…

A: Given data in question  Cross section Bending stress Length To find out  UDL value

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.7 in., b= 5.4 in., d= 4.3…

A: Mz = -4.35 kip-ft

Q: Resolve the Force F1 into components acting along the u and v axes and determine the magnitudes of…

A:

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

A:

Q: The wood beam supports loads of w = 440 lb/ft and P = 1020 lb on span lengths of LAB = 11.6 ft, LBc…

A: Given: The value of w is 440 lb/ft. The value of P is 1020 lb. The value of LAB is 11.6 ft. The…

Q: The stresses shown act at a point in indicated in the figure. Using the ed plane shown. Assume ß =…

A:

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

A:

Q: What is the specific weight in kN/cu.m of an oil with specific gravity of 0.75? What is the specific…

A:

Q: A 1.625-in-diameter solid steel shaft supports loads PA- 400 lb, Pc- 600 lb, and PE- 400 Ib, as…

A: