Two wooden planks, each 12 mm thick and 225 mm wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 20 MPa, determine the magnitude P of that axial load which will cause the joint to fail. provide your answer in kN with precision to two decimal points. 16 mm 16 mm ـة P 25 mm 50 mm 225 mm P 50 mm 25 mm

Two wooden planks, each 12 mm thick and 225 mm wide, are joined by the dry mortise joint shown. Knowing that the wood used shears off along its grain when the average shearing stress reaches 20 MPa, determine the magnitude P of that axial load which will cause the joint to fail. provide your answer in kN with precision to two decimal points. 16 mm 16 mm ـة P 25 mm 50 mm 225 mm P 50 mm 25 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A plank of wood is to be tested for its compressive strength, the cross-section of the timber is 200mmX200mm and 500mm tall. The result of the test gave 408KN before breaking. given E=9.72GPa Determine the maximum compressive stress taken by the wood a. 10.20MPA O b. 10.20Pa O c. 0.0102MPA O d. 0.0102Pa 22. Determine the elongation of the wood before breaking a. 5.246mm b. 52.46mm c. 0.05246mm O d. 0.5246mm
Q2. The joint connection shown in Figure Q2 is subjected to a medium term tensile load under service class C24. The joint comprises of six 3mm diameter x 150mm long wire nails. If the characteristic density of the timber is 340kg/m³, determine the load carrying capacity P1 and P2 of the connection and slip per nail P2 P 45 mm thick Figure Q2 75 mm thick P1 P1 P 100 mm thick
A pair of wood components having a dimension of 100mm X 100mm is joined by means of glue as shown. Determine the maximum axial load F, that most nearly can be subject to the woodpost without exceeding a maximum shear stress of 1650 KPa parallel to the cross section in kN.
The piece of wood, 100 mm by 100 mm in cross section, contains a glued joint inclined at the angle y to the vertical. The working stresses are 20 MPa for wood in tension, 8 MPa for glue in tension, and 12 MPa for glue in shear. If y ¼ 50 , determine the largest allowable axial force P.Show FBD of the three stresses
Two pieces of wood are glued together, find the maximum load which the glued wood could carry that must not exceed 12 MPa normal stress and 7 MPa shear stress. P 30° P 100 mm Glued Section 100 mm
12. Refer to figure 6. The 20-mm-diameter bolt fastens two wooden planks together. The nut is tightened until the tensile stress in the bolt is 150 MPa. Find the smallest safe diameter d of the washers if the working bearing stress for wood is 13 MPa. = 20 mm a. 70.8 mm b. 75.2 mm c. 86.3 mm d. 80.5 mm e. none of the above FIGURE 6
Question 4 A 6 KN force is applied at the free end of a wood (E = 12GPa) beam with dimensions given in Fig. Q4. Neglecting the effect of fillets and stress concentration, determine (a) the maximum compressive stress and its location at section A-A; (b) the maximum shearing stress and its location at section A-A; (c) the deflection at section A-A. 6 kN 300 mm 400 mm ΤΑ 叶 ¡A Fig. Q4 96 mm -- 12 mm 12 mm 48 mm
Two wood boards, each 16 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 760 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 7.0 kN. Use a = 18 mm and b = 144 mm. d Glue a P P a Answer: d= i b mm
A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the figure. The steel bar is 69-mm-wide by 8-mm-thick. For the steel bar, the yield strength is 235 MPa and the ultimate bearing strength is 350 MPa. The ultimate shear strength of the lag screws is 155 MPa. Factors of safety of 1.70 with respect to yield strength and 3.0 with respect to bearing strength are required for the bar. A factor of safety of 2.9 with respect to the ultimate shear strength is required for the lag screws. Determine the allowable load P that can be supported by this connection. (Note: Consider only the gross cross-sectional area of the bar-not the net area.) Support beam Answer: Pallow= 0000 P Steel bar KN
The built-up beam wooden above is subjected to a horizontal shear force, V, as shown. Assume that the beam dimensions are drawn to scale. Also assume that the nails attaching the three pieces of the cross-section allow it to act as a single member. Which of the following best explains why we cannot analyze the shear stresses in this beam with the techniques covered in this class (at least, so far)? The shear force is not "transverse" O Wood cannot be loaded perpendicular to the grain The shear force is not acting along a line of symmetry of the cross-section We can only deal with vertical shear forces
GIVEN: Steel / wood composite beam with cross-section shown Мnaк1.5 х 10° in-lb Esteel = 30 x 106 psi Ewood - 3 x 10° psi 11.5" '/4" REQ'D: A) Sketch transformed cross-section above. B) Calculate the transformed moment of inertia C) Maximum bending stress in the wood D) Maximum bending stress in the steel
The grains of wood in the board make an angle of 20° with the horizontal as shown. The board is subjected to an axial load of P = 300 N. (Figure 1) Part A Determine the normal stress that acts perpendicular to the grains. Express your answer to three significant figures and include the appropriate units. µA Value Units Submit Request Answer Figure < 1 of 1 Part B Determine the shear stress that acts parallel to the grains. Express your answer to three significant figures and include the appropriate units. HA -300 mm 160 mm Ta'y = Value Units 20° 25 mm1 Submit Request Answer