Two filter circuits are shown below.The first is a passive bandpass filter. Find the voltage transfer function, and(a)write your result in the form:H(m) Y (@)V (@) (1- Bo*)+ jAo(i.e., define A and B in terms of R, L, and C).L.leVoutinWhat is lim H(@) in terms of R, L, and C?What is lim ZH(o) in terms of R, L, and C?What is lim H()| in terms of R, L, and C?What is lim ZH(@) in terms of R, L, and C?Classify the filter as LP, HP, BP, or BS, and explain your reasoning.2.

Note: We are authorized to answer one question at a time since you have not mentioned which question…

Two filter circuits are shown below. The first is a passive bandpass filter. Find the voltage transfer function, and (a) write your result in the form: H(m)Y () V„ () ( ) + JAo 1-Bo (i.e., define A and B in terms of R, L., and C). L C Vin out What is lim H(m)| in terms of R, L., and C? What is lim ZH(m) in terms of R, L., and C? What is lim H()| in terms of R, L., and C? What is lim ZH(m) in terms of R, L, and C?

Two filter circuits are shown below. The first is a passive bandpass filter. Find the voltage transfer function, and (a) write your result in the form: H(m)Y () V„ () ( ) + JAo 1-Bo (i.e., define A and B in terms of R, L., and C). L C Vin out What is lim H(m)| in terms of R, L., and C? What is lim ZH(m) in terms of R, L., and C? What is lim H()| in terms of R, L., and C? What is lim ZH(m) in terms of R, L, and C?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the circuit of a low pass RL filter and find the transfer function. Cutwith a frequency of 70 HzDesign a low pass RL filter. The amplitude-frequency-curve of this filter you designed.Draw in accordance with the calculated values.
As part of a radio receiver, you are asked to design a simple bandpass filter using a series inductor, capacitor and resistor. The filter needs to pass a centre frequency of f0 = 1089 kHz with a bandwidth of 9 kHz. Do this by finding the capacitor and resistor values together with a 240 uH inductor that will give you the correct centre frequency and bandwidth. Also, calculate the quality factor Q for your filter. Sketch the filter circuit and show all your calculations.
What is the distinction in voltage attain of a lowpass filter if the enter frequency is doubled? What is the distinction in voltage attain of a lowpass filter if the enter frequency is expanded ten times? How do you assemble a band give up RC filter? Simulate a circuit and generate a desk to show your claim.
Determine the transfer function from Uin to Uut! b) Set up amplitude and phase function! c) Assume that we connect 10V (DC) as input voltage at time t-0. How much voltage is then above C2 after a long time?
4. A simple band-pass filter can be designed by cascading one-pole high-pass and one-pole low-pass filters. Using op- amp circuits similar to the one shown below, design band-pass filter with cutoff frequencies of 200Hz and 50 kHz and with a midband gain of 10dB. Resistor values must be no larger than 200k, but the input resistance must be as large as possible. Vic C oV₂ V₁ www OV
Answer the following wuth illustration and solutions. 1.) A second-order band pass filter is to be constructed using RC components that will only allow a range of frequencies to pass above 500Hz and below 1.5kHz. Assuming that both the resistor have values of 1kohms, calculate the values of the two capacitors required. Find also the center frequency of the two frequencies. This is the example/guide that might help.
5. You are given the signal x(n) at a sampling rate of 1500 Hz, and you want to convert it to a signal y(m) with a 2400 Hz sampling rate such that the signals have equivalent spectra. Design a system that will do this. You may use ideal frequency selective filters in your design.
Question 4 Consider the following RL filter: L1 V1 ac 1 out .ac dec 10 1 100000 R1 6.28k Find the cut-off or cut-in frequency. What kind of filter is this circuit? Low-pass? High-pass. Describe the frequency response in terms of gain before or after the cut-off or cut-in frequency and how steeply the frequency response curves goes down or up after or before the cut-off or cut-in frequency. Express the "steepness" in dB/decade. You may use LTspice to find these values.
Design a filter using the window method and provides the specifications for the filter design. Here is a summary of the specifications given: Stopband: [0 kHz, 4 kHz] Passband: [5.5 kHz, 16 kHz] Maximum ripple in the passband: 0.1 dB Minimum attenuation in the stopband: 51 dB Sampling frequency: 32 kHz The task is to design a filter (by hand, with the impulse response formula) that meets these specifications.
Briefly -Discuss the effect of increasing the order of the filter on the frequency response of the filter.
Consider a step down converter supplied by a DC power source of magnitude Vs = 100 V. The switching period is 0.2 ms. The load is resistive with R-5 Ohms. An LC filter is used to regulate the output with L- 5 mH and C-200 uF. The switch is ideal. The average output voltage is Va= 50V. The ripple current of the inductor delta (1) and the ripple voltage of filter capacitor delta (V) are respectively equal to: Select one: O a. 1A, 0.125V O b. 0.9A, 0.1V O c. 0.96A, 0.12V O d. None of these
Fill in your bole algebra training with karnaugh in the image.(Do not discount.)