Through a very narrow gap of height 'h' a thin plate of large extent is pulled at a velocity V. On one side of the plate oil of viscosity μ, and on other side oil of viscosity μ₂. Calculate the position of plate so that: (i) The shear force on two sides of plate is equal (ii) The pull required to drag the plate is minimum

Through a very narrow gap of height 'h' a thin plate of large extent is pulled at a velocity V. On one side of the plate oil of viscosity μ, and on other side oil of viscosity μ₂. Calculate the position of plate so that: (i) The shear force on two sides of plate is equal (ii) The pull required to drag the plate is minimum

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEMS 237. The lower ends of the three bars in the figure are at the same level before the rigid homogeneous 18Mg block is attached. Each steel bar has an area of 600mm² and E=200GPa. For the bronze bar, the area is 900mm² and E-83GPa. Find the stress developed in each bar. BRONZE 1.6M STEEL 1M 18Mg STEEL 1M ТЕСНА
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The force system acting on the machine part is equivalent to the single force R=475i+50j acting at O. (a)Find the value of P. (b)What is the value of the y-component of P? (c)Find the value of b. (d)What is the value of x-component of P?
Hiw the cross- Sectional dimensiuns of a beam are shown below. If the makimum allowabhe benehing stresS 600 Mpa. Determine the mx imum beneliny ma gnitude (M) thut Can be suppurtel by the beam. Supporn the syn is ef bending is positive. 75mm 1% mm Hw:: A beam had subjected to a postive bending moment of 5 KN. m. The Cross-Sedional dimensions are shown below. Draw the bending stress distribution on the Cross- Sedion. loo mm 15 mm 15a wm 13 mm
5- The solid rod is subjected to the loading snown. Determine the state of stress at point A, and show the results on a differential volume element located at this point. (HINT: For 100 KN load, the bending will happen about a vertical axis passing through the centroid.) 100 KN 10 KN 200 mm 20 AN 30 mm
A rectangular cantiliver wooden beam is applied by point load of 400in at free end Determine cross section area and second moment of inertia about bending axis and Draw internal effects shear and bending diagram Determine direct and shear stress at A on cross section of a-a .sketch state of stress
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
А P 200 mm В E 150 mm F Three steel (E=200 GPa) rods (AB, CD and EF) support a load of P=30 kN as shown in the figure. Each of the rods AB and CD has a 80-mm2 cross-sectional area and rod EF has a 120-mm2 cross-sectional area. (a) Write the equilibrium equation for the rigid member BED in vertical direction, (b) write the compatibility equation for the given bar system, (c) determine the force in rod EF (d) determine the average normal stress in rod EF.
7.A cast-iron machine part is acted upon by the 3kN.m couple shown. Knowing that E=165GPA and neglecting the effect of fillets. i) Determine the maximum tensile and compressive stress in the casting ii) Determine the radius of curvature of the casting. 90 mm 20 mm 40 mm 30 mm M = 3 kN m
Situation 2| The compound shaft as shown is attached to rigid supports. It is subjected to a concentrated torque at the junction. The length of the steel segment is 1m. 3. Determine the ratio of the length of the steel segment to that of the bronze such that the materials will be stressed to their limits. 4. Determine the torsional reaction, in N-m, at the right supports if the applied torque at the junction is maximized. 5. Determine the angle of twist, in ° degrees, at the junction. Bronze = 75 mm G = 35 GPa T= 60 MPa Steel = 50 mm G = 83 GPa = 80 MPa %D Tll IA a b.
H.W.1: A rigid steel bar ABC is pinned at B and supported by two rods at A and C. There is no strain in the rods before load P is applied. After load P is applied, the axial strain in rod (1) is +910 pe. Determine the axial strain in rod (2). (1) C 2,000 mm 520 mm ad Na 400 mm 1,250 mm A (2)
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm