The Zn in a 0.6185 g sample of foot powder was titrated with 23.74 mL of 0.01485 M EDTA. Calculate the % Zn in this sample. Answer: %Zn = ____ %
Q: 3. A 0.1093-g sample of impure Na2CO3 was analyzed by the Volhard method. After adding 50.00 mL of…
A: Given , mass of impure Na2CO3=0.1093 gVolume of AgNO3= 50.00 mLConcentration of AgNO3=0.06911…
Q: Aspirin powder = 0.8110g MW of Aspirin = 180g.mol-1 Volume of 0.5N HCl consumed in back titration…
A: Volume of 0.5N HCl consumed in back titration = 23.50 mL
Q: 5. A vinegar sample of 19 mL was diluted with distilled water to a 250-mL volume. 25 mL portion of…
A: Acid-base titration: Titration is a method to determine the concentration of unknown acid by using…
Q: 10. The color change of a chemical indicator requires an over titration of 0.03 mL. Calculate the…
A: Given, The error in measurement = 0.03 mL The experimental values are 50.00 mL, 10.0 mL, 25.0 mL,…
Q: In the next part of the experiment, you used the standard solution of sodium oxalate to standardize…
A:
Q: The zinc contained in a 0.7555-g sample of foot powder was titrated with 21.27 mL 0.01645 M EDTA.…
A:
Q: A 47.00 ml aliquot from a 0.490 L solution that contains 0.410 g of MnSO, (MW = 151.00 g/mol)…
A:
Q: A 100.0-ml sample of boiler feed water, analyzed for hardness, required 36.8 ml of 0.0386 M EDTA to…
A:
Q: A foot powder sample containing Zn was dissolved on 50.00 mL water and was titrated to the end point…
A:
Q: A 0.500 g of impure Na2CO3 is analyzed by adding 50.0 mL 0f 0.100 N HCl, a slight excess. Boiling…
A:
Q: 100 mL of mineral water containing Mg2+ and Ca2+ is taken and titrated with 86.65 mL of 0.06120 M…
A: We know that EDTA forms 1:1 complex with metals Mg+2 and Ca+2 Initial moles of EDTA = M*V =…
Q: A foot powder sample containing Zn was dissolved on 50.00 ml water and was titrated to the end point…
A:
Q: A 1.025 g sample containing Cl- is analyzed through the Mohr method. The sample is dissolved in 250…
A: Given that - Mass of a sample containing Cl- ions = 1.025 g Volume of Solution prepared = 250 mL…
Q: Does any solid Cu(OH)2 form when 0.075 g of KOH is dissolved in 1.0 L of 1.0×10-3 M Cu(NO3)2? (The…
A: A question based on Ksp, which is to be accomplished.
Q: A 5.00 mL tap water sample was measured out with a volumetric pipette, and added to a 25 mL…
A: Given : volume Na2EDTA.2H2O used = 0.635 mL Concentration of Na2EDTA.2H2O = 0.0100 M And volume of…
Q: A hydrated sample weighing 0.2700 g was shaken with 50.0 mL of anhydrous methanol and titrated with…
A: Solution- Data given-A hydrated sample weighing 0.2700 g, 50.0 mL of anhydrous methanol , 0.0150 M…
Q: Jessica made 300 mL of primary standard using 2.35 g of sodium carbonate. She then conducted a…
A: Given - Mass of primary standard, sodium carbonate = 2.35 g and its volume is = 300…
Q: A 20-mL solution of 0.0659 M AgNO3 was titrated with 20 mL of 0.0509 M NaCl (Ksp = 1.8x10-10).…
A: 20 mL of 0.0659 M AgNO3 solution was titrated with 20 mL of 0.0509 M NaCl solution .The Ksp is…
Q: A foot powder sample containing Zn was dissolved on 100.00 mL water and was titrated to the end…
A: The question is based on the concept of complexometric titrations. We have to calculate pZn value.
Q: An EDTA solution prepared from its disodium salt was standardized using 0.250-g primary standard…
A: The question is based on the concept of quantitative estimation. We have to determine hardness of…
Q: 20.0 mL water sample was titrated with 0.0100 M EDTA solution that required 14.50 mL for CaCO3…
A: Here we have to determine the hard ness of hard water interms of CaCO3 if 20 mlbof hard water sample…
Q: Five white, 500-mg uncoated ascorbic acid (AA) tablets with an average weight of 0.6100-g were…
A: To calculate the amount of ascorbic acid present in a uncoated ascorbic acid tablet having an…
Q: The thiourea in a 1.455 g sample of organic material was extracted into a dilute sulfuric acid…
A: In chemistry, there are many ways to check the deviation of experimental data from the accurate…
Q: 5. A vinegar sample of 19 mL was diluted with distilled water to a 250-ml volume. 25 mL portion of…
A: Volume (V 1 ) of NaOH consumed= 27.1mL Concentration( M1) of NaOH solution = 0.02mol/L Volume(V 2)…
Q: percentage thiourea
A:
Q: Excess Ca(OH)2 is shaken with water to produce a saturatedsolution. The solution is filtered, and a…
A:
Q: A 0.1504-g sample of impure Na₂CO₃ (106.00g/mol) was analyzed via Volhard method. After adding 50.0…
A: Here we are required to find the purity of Na2CO3.
Q: A sodium thiosulfate solution is standardized using pure copper as the primary standard. A sample of…
A: Given data, Mass of Cu = 0.2624 g Volume of sodium thiosulfate =…
Q: 3I- + OCl- + 2H+ ----> I3- + Cl- + H2 : A 25.00 ml sample of liquid bleach was diluted to 1000 ml in…
A: welcome to bartleby, answer to the question is provided below.
Q: Standardization of EDTA was done using MgSO4 standard wherein a 50-mL aliquot of solution obtained…
A: Mass of MgSO4 = 0.480 g in 500 mL (0.500 L) Volume of MgSO4 = 50 mL Volume of EDTA = 39.4 mL Mass…
Q: Table 8.1 Hardness determination of water samples. mL of Volume of NazH2Y 2 H2O, mL Ca2+, mg/L…
A: First you have to standardize the EDTA solution before the titration of hard sample solution. Let…
Q: A 15.00 g sample containing mixed alkali and other inert components was dissolved and diluted to 300…
A: We have find out the The volume of titrant needed to neutralize NaOH is _________ mL.The volume of…
Q: A 0.2185 g sample of NaCl was assayed using Volhard method using 50 mL of 0.998N silver nitrate and…
A: In the Volhard method, silver nitrate is titrated with chloride solution (NaCl) and then excess…
Q: A 0.1093-g sample of impure Na2CO3( Molecular weight 106) was analyzed by the Volhard method. After…
A: Given: 1) The reaction taking place: Na2CO3 + 2AgNO3 → Ag2CO3 + 2NaNO3 2) The reaction of KSCN with…
Q: What is the mass of pure dry CaCO3 (MW: 100.0869 g/mol) standard used in the standardization of EDTA…
A: A question based on mole concept that is to be accomplished.
Q: What is the MW of calcium carbonate?
A: Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: Cobalt is often added to steel in order to increase its hardness. The cobalt content of 5 different…
A: Solution The data provided are: Sample Titration Spectroscopy (x-mean)2 for titration (x-mean)2…
Q: On titrating 50 ml of 0.01 M KI with 0.01 M AgNO3 . The value of pAg after addition of 30 ml AgNO3…
A: Given data, Volume of KI or I- = 50 ml (as KI is a strong electrolyte, it is completely…
Q: A 100 mL of 0.375 M CH3COOH solution was shaken with 1.0 g charcoal for 5 min. After filtration, 10…
A: I have given a detailed solution to the question as follows:
Q: You collected the following data from a titration experiment using a 0.123M standardized NaOH…
A: Initial burette reading = 0.56 ml Final burette reading = 19.20 ml Volume delivered (ml ) = ?
Q: To determine the concentration of an EDTA solution, the following zinc(II) solution is prepared:…
A: metallic zinc (m(Zn) = 0.301 g) is dissolved in dilute sulfuric acid, the resulting solution is…
Q: What is the mass of pure dry CaCO3 (MW: 100.0869 g/mol) standard used in the standardization of EDTA…
A:
Q: 25.00 mL of 0.041 32 M Hg2(NO3)2 were titrated with 0.057 89 M KIO3. Hg++ 2103 →→ Hg₂(103)2(s)…
A: Since you have asked a question with multiple sub-parts, as per our company guidelines we are…
Q: A standard CaCO3 solution is prepared by dissolving 0.4193g in enough dilute HCl to effect solution…
A: The given data contains, weight of CaCO3 =0.4193 g volume of EDTA =23.62 ml
Q: In the titration of 25.00 mL of a water sample, it took 20.840 mL of 4.350x 10−3 M EDTA solution to…
A:
Q: A freshwater sample containing Ca2+ and Mg2+ will be analyzed using EDTA titration. The EDTA titrant…
A:
Q: Calculate the volume of 0.0500 M EDTA needed to titrate 29.13 mL of 0.0598 M Mg(NO3 )2. Use a MW…
A:
Q: A solid sample containing chloride and with a mass equal to 6.000 g was dissolved in water and…
A: Balanced chemical equation for the given reaction is: Cl- + AgNO3 → AgCl + NO3- This means that 1…
Q: her 250.00 mL sample was then treated with NaOH to precipitate Mg(OH)2 and was then titrated at pH…
A:
Q: The Zn in a 0.8872-g sample of foot powder was titrated with 24.24 mL of 0.01842 M EDTA. Calculate…
A: Given data: The volume of EDTA=24.24 mL=0.02424 L. The molarity of EDTA=0.01842 M = 0.01842 mol/L.…
The Zn in a 0.6185 g sample of foot powder was titrated with 23.74 mL of 0.01485 M EDTA. Calculate the % Zn in this sample.
Answer:
%Zn = ____ %
Step by step
Solved in 4 steps
- Molarity of Na2S2O3 (stock solution). 0.100 M Volume of diluted bleach titrated (taken from the volumetric flask). 10ml Initial Burette Reading. 14.80 Final Burette Reading 25.60 Volume of Na2S2O3 used in the titration (mL). 10.80 Moles of Na2S2O3 used in the titration. 1.71 Moles of S2O3–2 used. 1.66 Moles of I2 initially present in titration mixture 0.83 Moles of NaOCl in the diluted bleach titrated. 0.415 Volume of bleach titrated. 1ml Mass of commercial bleaching solution titrated ?Molarity of Na2S2O3 (stock solution). 0.100 M Volume of diluted bleach titrated (taken from the volumetric flask). 10ml Initial Burette Reading. 14.80 Final Burette Reading 25.60 Volume of Na2S2O3 used in the titration (mL). 10.80 Moles of Na2S2O3 used in the titration. 1.71 Moles of S2O3–2 used. 1.66 Moles of I2 initially present in titration mixture 0.83 Moles of NaOCl in the diluted bleach titrated. 0.415 Moles of OCl– in the diluted bleach titrated. ?Molarity of Na2S2O3 (stock solution). 0.100 M Volume of diluted bleach titrated (taken from the volumetric flask). 10ml Initial Burette Reading. 14.80 Final Burette Reading 25.60 Volume of Na2S2O3 used in the titration (mL). 10.80 Moles of Na2S2O3 used in the titration. 1.71 Moles of S2O3–2 used. 1.66 Moles of I2 initially present in titration mixture 0.83 Moles of NaOCl in the diluted bleach titrated. 0.415 Volume of bleach titrated. 1ml Mass of NaOCl in commercial bleach titrated. ?
- A 0.9092g sample of wheat flour was analyzed by Kjeldahl method. The ammonia formed was distilled into 50.00 mL of 0.05063 M HCl; a 7.46 mL back titration with 0.04917 M NaOH was required. Calculate the % protein in the flour. Input the value only. Express in 2 SF.A (aq) + ...B(aq) C(s) + D (aq) ... .. Experimental | Volume of B/ mL Mass of Run precipitate/g 1 1.2 5.40 2 1.4 7.24 1.6 9.02 4 1.8 9.90 2.0 10.86 6. 2.2 10.90 7 2.4 10.88 8 2.6 10.84 9. 2.8 10.86 A series of experiment was performed to determine the mole ratio of a given reaction. 1 mL of 1 Molar A added to nine beakers, then the increasing amount of 1 Molar B added to these beakers. Volume of B and mass of precipitate of C are given in the table below. Find the mole ratios through plotting a graph.A 0.1093-g sample of impure Na2CO3 was analyzed by the Volhard Method. After adding 50.00 mL of 0.06911 M AGNO3, the sample was back titrated with 0.05781 M KSCN, requiring 27.36 mL to reach the end point. Report the purity of Na2CO3 sample.
- Exp. 4 Volhard method In an experiment of determination of KBr (g%) by volhard method In a flask; 15ml KBr was taken 25 ml 0.05M AgNO3 1 ml nitric acid 1 ml ferric alum indicator Then titration with 0.05M KSCN was done The end point was =15 ml Calculate the mass of KBr in g%AaBbCcDd AaBbCcDd AaBbC AaBbCcD AdD AaBb- 1 Normal 1 No Spac... Heading 1 Heading 2 Title Subti 田,、 即咖山 Paragraph Styles 1. 3. 2.15.0 mL HNO3 was titrated to equivalence with 60.0 mL of 0.020 NaOH. What is the concentration of the acid? 近0 of F5 F7 6日 てい いレゴPart A) A 10.0 mL sample of 0.250 mol/L NiF2(aq) is mixed with 20.0 mL of 0.0900 mol/L NaOH(aq) and then diluted to a final volume of 100. mL.Calculate the concentration of Ni2+ ions in the 100 mL mixture before the reaction starts. Express your answer to three significant figures.ksp: 5.48e-16
- A 0.1214-g sample of impure Na2CO3 was analyzed by the Volhard method. After adding 50.00 mL of 0.07011 M AgNO3, the sample was back titrated with 0.06021 M KSCN, requiring 27.15 mL to reach the end point. Calculate the purity of the Na2CO3 sample.A 500.0-mg sample of waste ground coffee beans used as fertilizer was digested and analyzed for nitrogen using the Kjeldahl method. After digestion, the distilled ammonia was collected in 100 mL of 0.5500 M boric acid. This solution required 19.60 mL of 0.5880 M HCI for titration to the methyl red end point. Calculate the %N in the fertilizer. Prelim Rxn: NH3 + H3BO3 --> NH4: H2BO3 Titration Rxn: NH : H2BO3 + HCI --> H3BO3 CI-5. A 300.0 mg sample containing Na,CO3, NaHCO, and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1000 M HCI the titration required 24.41 ml to reach the phenolphthalein endpoint. And an additional 8.67 mL to reach the methyl red endpoint. Determine the composition of the sample and calculate the percent of each titrated component.