The zero-state scaled network shown in Figure 134 is driven by the sinusoidal current source Jg(t) expressed as J,(1) =VZsin(2r-45°).4 Use phasors and complex immittances to calculate the following: (a) the node voltages Val and Va2 as complex mumbers in rectangular and polar format, and (b) the node voltages val(t) and vn2(t) in the time-domain. L2 0.5H Vai(t) Vnz(t) + v-(t) J(t) g-V2(t) C3 1F R, 10 (gm = 3S) Figure 134 Scaled RLC network

The zero-state scaled network shown in Figure 134 is driven by the sinusoidal current source Jg(t) expressed as J,(1) =VZsin(2r-45°).4 Use phasors and complex immittances to calculate the following: (a) the node voltages Val and Va2 as complex mumbers in rectangular and polar format, and (b) the node voltages val(t) and vn2(t) in the time-domain. L2 0.5H Vai(t) Vnz(t) + v-(t) J(t) g-V2(t) C3 1F R, 10 (gm = 3S) Figure 134 Scaled RLC network

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Figure 2 shows three "LC" circuits, two of them with capacitance capacitors "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitance capacitors "Cc". The currents that circulate through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = −dQ / dt, find the system of coupled equations of the system and then find the normal angular frequencies of the system.
The picture shows three LC circuits, two of them with capacitors of capacitance C and the three with coils of inductance L, the three circuits are coupled by means of two capacitors Cc capacitors.L inductance coils, the three circuits are coupled by means of two capacitors of capacitance Cc. The currentscirculating through each mesh are those indicated in the figure: I1, I2 and I3. Using Kirchhoff's law for voltagesand taking into account the definition of current I = -dQ/dt, find the system of coupled equations for the systemand then find the angular normal frequencies of the system.
Based on Figures la,1b and 1c and RLC elements, write a discussion on voltage-current relations and power factor.
Determine the capacitance and voltages (Vrms) across the resistor and capacitor and prove that the phasor sum of the series components is equal to the source voltage. Also, solve for its total circuit impedance and total circuit current.
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of 1ohm and an inductance of 10mH, find the source voltage. 5A 2A ton toff output _current
A) find Ztot in rectangular form B) find Ztot in polar form C) find V1 or VL in polar for. ( use voltage divider rule or ohm law).
Write a report to compare between Ac Through capacitance and AC through in inductance then: For the circuit shown beside, find the total impedance between a and b and Circuit current (I)
In alternating current, AC, theory, the voltage through an inductor leads the current by a phase angle of 90°. Complex numbers can help in this situation as when a real number is multiplied by i it rotates through 90° on the Argand diagram, with the magnitude remaining the same. This allows us to specify the impedance through an inductor as a complex number. This can be combined with a resistor to give a combined impedance of z = r + Li. If we have two such elements in a circuit, we can use complex numbers to determine the total impedance when they are in series and in parallel. In series Zt = Z1 + Z2 In Parallel Add the following two impedances (a) in series and (b) in parallel. Z1 = 4 + 3i and Z2 = 12 + 5i
What impedance vector - j25 represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a resistance.
PHASE RELATIONSHIP SINUSOIDAL( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
In alternating current, AC, theory, the voltage through an inductor leads the current by a phase angle of 90°. Complex numbers can help in this situation as when a real number is multiplied by i it rotates through 90° on the Argand diagram, with the magnitude remaining the same. This allows us to specify the impedance through an inductor as a complex number. This can be combined with a resistor to give a combined impedance of z = r + Li. If we have two such elements in a circuit, we can use complex numbers to determine the total impedance when they are in series and in parallel. In series Zt = Z1 + Z2 In Parallel