PROBLEM 2The two forces are equivalent to a force R that has a line of action passingthrough point A. Determine R and the distance X.ķ200mm-f100 NNX90mm

Answered: Image /qna-images/answer/84605755-2ce3-452d-88b4-65de59c15aae.jpg

Answered: The two forces are equivalent to a…

The two forces are equivalent to a force R that has a line of action pass through point A. Determine R and the distance X. 200mm-f 100 N 490 N 90mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: DETERMINE THE CENTROIDAL MOMENT OF INERTIA

A: Given:- size of plate 14"X1/2" depth of web 14.5" size of angle attached with plate and web…

Q: Problem no. 1. Compute the reaction forces at pt. A and B D C A 9m B 3m 1.5 m 3 m 30° 20 KN

Q: Problem: Determine the deflection specified in each of the following beams. Assume constant El. Use…

A: Given: A propped cantilever beam with internal hinge at a distance 3m from fixed support. To find:…

Q: # 3A. The rigid bar AB, attached to two vertical rods as shown, is horizontal before the load P is…

A: Given, P = 50 kN Lal = 3m Lst = 4m Eal = 70 GPa Est = 200 GPa

Q: A rectangular plane surface is 2 m wide and 3 m deep. It lies in vertical plane in water. Determine…

A: Given Data- Width of plane surface b=2 m, Depth of plane surface d=3 m, To find- The total pressure…

Q: Use the virtual work method for solving problems 13.7 through 13.30. E=29x10^6 psi for all problems…

Q: 9-21. Determine the slope and displacement at point C. Use the principle of virtual work. El is…

A: Given data Find slope and deflection at C using virtual work method.

Q: Compute the value of discharge through pipe having cross sectional area of pipe is 4 m2 and flow…

A: Introduction : The given question is related with fluid mechanics . In this question we are provided…

Q: Do all groundwater contaminants behave the same way (float, sink, become aqueous)?

A: Groundwater : It is the subsurface water that can be discovered in the voids and fissures of rocks,…

Q: PROBLEM NO. 2 (Truss) Classify the plane truss shown as unstable, statically determinate, or…

A: Given: A simply supported truss with hinge support at A and roller support E. Method used: (1)…

Q: For the simply supported beam shown below (hinge support at A and roller support at D). a) By…

Q: The composite beam is made of steel (A) bonded to brass (B) and has the cross section shown. It is…

A: Given data Est = 200 GPA Ebr = 100 GPA Find A. Maximum bending stress in brass B. Maximum…

Q: Define metamorphic foliation. Under what kind of stress does metamorphic foliation form?

A: Foliation:- If flat or elongated minerals within a rock are compressed and aligned, foliation is…

Q: Problem 2: A cylinder of diameter D, length Lis immersed in a fluid that flows perpendicularly to…

A: Buckingham Pi method for dimensional method is applied to create dimensional similarity in the given…

Q: This "I-shaped" cross-section is often used for beams because the moment of inertia about the…

A: Given data Find moment of inertia about strong axis (I) using subtractive method or additive…

Q: Q2- B: Soil has been compacted in an embankment at a bulk unit weight of 21.1kN/m³ and water content…

Q: DETERMINE THE CENTROIDAL MOMENT OF INERTIA X W14 X 30 CIOX 15.3 9.12 [231.7mm]

Q: Which of the following are common software for Design / Constructability Review? AutoCAD or…

Q: a) The rate of an item of werk is not depends on Specifications of materials. h) The brick work is…

A: Reference : Building Material, Brick work To determine : True or false with valid reasons. Note : As…

Q: 1. A soil-mantled hillslope with horizontal dimensions of 250 m x 250 m has a uniform slope of 0.3.…

Q: A packing crate of mass 40 kg is pulled by a rope as shown. The coefficient of static friction…

Q: 5. Method of Sections: Using the method of sections (no other method is acceptable), determine the…

Q: Draw the shear and bending moment diagram for the following structure w = 10 lb/ft w = 10 lb/ft -2…

A: Given : we have to draw the shear and bending moment diagram for the structure shown above

Q: The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the…

Q: Draw the shear and moment diagrams for the beam. A 400 lb/ft -4 lt -2 ft- 0 B -3 ft 900 lb-ft

A: Loading and beam length are given. Draw SFD & BMD.

Q: 2. You measure the shear strength of a clayey soil sample to be 41 kPa at an effective normal stress…

A: Here we have given two soil samples and we have to calculate the angle of friction of soil sample…

Q: "A simply supported unreinforced concrete test beam spanning 1.8 m shown in the Figu below. The beam…

A: Given :- the cross section dimension is width of the beam b= 100 mm and depth of the beam d=…

Q: Situation #5 CE Board May 2015 A 9 m. cantilever retaining wall is subjected to active pressure…

Q: of a wall. The beam is subjected to a X KN concentrated load at 2 m. from the wall and a uniformly…

A: For Shear Force and Bending moment we take help of equilibrium condition. Standard result of…

Q: A cable supported at points A and B 210m horizontally apart with B 30m higher than A. The cable sags…

Q: solve for the angular deformation of one end relative to the other end

Q: m, tf = 12.80 mm and tw = 7.7 mm. The section is acted by a tensile force and attached to onnectors…

Q: Problem2 The planar truss shown in the figure below (fig.2) is a structure composed of slender…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: Q.3) Two structural members AB and BC (shown below) are connected by a 0.75- inch diameter pin at B…

A: Pin diameter= 0.75 in Maximum average normal stress in members AB and BC

Q: *3-116. The horizontal 30-N force acts on the handle of the wrench. Determine the moment of this…

Q: Four people are attempting to move a stage platform across the floor. If they exert the horizontal…

Q: Determine the force in each member of the truss 2+A m 1+ B B 5 kN -2 m- -2m- Y KN 11. What is the…

Q: A torque of T = 1900 Nm is applied to each of the fixed supported bars as shown in Fig. 1. a)…

A: Given : T = 1900 Nm To Determine :

Q: Calculate the mass (kg) of a fluid having a volume of 2 m^3 and unit weight of 11.2 kN/m^3.

Q: Situation #1 The compound beam is pin supported at C and supported by a roller at A and B. There is…

A: Note:- As per our company policy in case of multiple parts questions, we can solve only first 3…

Q: 13.18 Determine the deflection at the centerline and the slope at the right end of the beam shown in…

Q: A high-density polyethylene [E= 104 ksi and a 74 x 10-6/°F] block (1) is positioned in a fixture.…

Q: 1.11 Member 1 in the structure shown in Figure P1-11 undergoes a temperature increase of 50°F. Using…

A: Reference : Engineering Mechanics, Elongation and deformation. Given : E , alpha, Length area and…

Q: In a two peg test of a dumpy level using alternative method, the following observations were taken.…

Q: Determine the forces for members GF, GD, and CD using Method of Section. Indicate if (T) or (C)

A: Given Data Find force in member GF, GD and CD using method of section

Q: DETERMINE THE CENTROIDAL MOMENT OF INERTIA

A: Given:- I section To find:- moment of inertia about centroidal axis

Q: Generating project specs from BIM data is the only means to create a specification deliverable True…

A: No Generating project specs from BIM data is the only means to create a specifications delivered.…

Q: Problem 3 Compute the nominal compressive strength of the member shown. Use the theoretical value…

A: Given Data:Member HP 16×121 A572 Grade 55Length of member = 14 feet To…

Q: peam has fixed support on the left side and a roller on the right side. Bending is about -axis.…

Q: What is the vadose zone, capillary fringe zone, and phreatic zone

A: Groundwater:- Water that is underground and can be found in voids and cracks in sand, rock, and…

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

PROBLEM 2
The two forces are equivalent to a force R that has a line of action passing
through point A. Determine R and the distance X.
ķ
200mm-f
100 N
N
X
90mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine all the values of m of the auxiliary equation of the differential equation. d²y :5 dr? d*y 4y
PROBLEM 1 The force system acting on the machine part is equivalent to a single force with components Rx= 475 N directed to the right and Ry =50 N directed upwards. Determine the force P and the distance b. 1500 N+ 240 mn !. 300 N 30° 120 mm 1000 N
g) the value of the constant of integration C4. Enter your answer in kNm3 to 3 decimal places.
Verify whether the system of forces shown can be replaced by a single equivalent force. If it can be replaced determine the point where the line of action of the single equivalent force intersects with the xz-plane. Note: If the system cannot be simplified into a single equivalent force system, write CS (Cannot be Simplified) into the answer box. y A 12 kN 30 kN B 18 kN 300 mm 18 kN 30 kN 500 mm 400 mm D 16 kN
Suppose that vc=4.5 ft/s. (Figure 1) Figure 1 ft B A 3966666 Te 3 ft < 1 of 1 Part A Determine the angular velocity of link AB at the instant 0 = 30° measured counterclockwise. Express your answer in radians per second to three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise. WAB = Submit Part B 17 ΑΣΦ 跖 ↓↑ vec X Incorrect; Try Again; 4 attempts remaining WBC = Previous Answers Request Answer ? Determine the angular velocity of link BC at the instant 0 = 30° measured counterclockwise. Express your answer in radians per second to three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise. —| ΑΣΦ. 11 | vec ww rad/s ? rad/s
State the order of the given ordinary differential equation. (1 x)y" - 4xy' + 7y = cos x Determine whether the equation is linear or nonlinear by matching it with (6) in Section 1.1. dny an(x) + a dxn ²n-1(x)_ d-ly + ... + a₁ (x) - dxn-1 dx - 2₁ (x) dy + + a(x) y = g(x) (6) linear O nonlinear
ths 25 Q4) Figure (Q4) shows vectors A and B. Find vector C such that vectors A + B+C = 0. Write your answer in (i.j) .component form y 4 m B2 m 40° 10°
Vector O is the resultant of vector M = 9.9i + 3.8j + -3.5k and an unknown vector N. Vector O is a vector in the positive z-direction only and has twice the magnitude of vector M. What is the magnitude of vector N? Express your answers in two decimal places.
(b) Two connected steel bars as shown in Figure Q2(b) are axially loaded with 100 N at node 3. The cross section area for bar B is half of bar A. The horizontal displacement at node 2 is half of displacement at node 3. By using finite element method, determine the displacement at node 2 and node 3. The modulus of elasticity is constant.
Q3/ Determine the magnitude and the direction of the resultant force. (Use Cartesian vector expression in your solution) F1= 500 N F2= 400 N 10 6. 8 y 45 ° 60 o х-у plane
please
1) An object, having a weight of 20 N, moves from point A to point B on a smooth surface of a path in a three-dimensional space. The x- y- and z- coordinates of the points are given respectively in meters: A (0; 3; 3), B (6; 5; 0). The speed of the object at point A is 18m/s and the force [F = 2x i+ 3y j+z k] N is acting on the object during the motion. What is the speed of the object at point B? 2) The acceleration of a 2kg - body along straight line is expresses as a = -0.002 v² m/s². The initial velocity of the body at the beginning of its motion is vo. How far does the body travel until its velocity becomes the half of its initial velocity? 3) A 105gr-baseball moves in the horizontal direction to the right with a velocity of 18m/s. After the baseball is hit with a 3kg - bat, it moves to the left, in a direction 20° from the horizontal with a velocity of 38m/s. If the duration of interaction between the baseball and the bat is 0.028s, what is the average impulsive force (its…