The synchronous generator in Figure is initially operating in the steady-state when a permanent three-phase-to-ground bolted short circuit occurs on line 1-3 at bus 3. The fault is cleared by opening the circuit breakers at the ends of line 1-3 and line 2-3. These circuit breakers then remain open. The infinite bus receives 1.0 per unit real power at 0.95 p.f. lagging, H = 3MJ/MVA. Assume Pm remains constant throughout the disturbance. Determine whether stability is or is not maintained and determine the maximum power angle. B12 B21 X12 = 0,20 G XTR = 0.10 811 X = 0.30 00 F Vous = 1.0 822 = X13 0.10 X2 = 0.20 813

The synchronous generator in Figure is initially operating in the steady-state when a permanent three-phase-to-ground bolted short circuit occurs on line 1-3 at bus 3. The fault is cleared by opening the circuit breakers at the ends of line 1-3 and line 2-3. These circuit breakers then remain open. The infinite bus receives 1.0 per unit real power at 0.95 p.f. lagging, H = 3MJ/MVA. Assume Pm remains constant throughout the disturbance. Determine whether stability is or is not maintained and determine the maximum power angle. B12 B21 X12 = 0,20 G XTR = 0.10 811 X = 0.30 00 F Vous = 1.0 822 = X13 0.10 X2 = 0.20 813

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.3MCQ: The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of...

See similar textbooks

Similar questions

Description In the particular case of figure below derive both the critical clearing angle and the critical clearing time. P, = Pmaz sin d Pm A1 do der Smar A generator having H = 6.R MJ/MVA is delivering power of 1.0 per unit to an infinite bus through a purely reactive network when the occurrence of a fault reduces the generator output power to zero. The maximum power that could be delivered is 2.5S per unit. When the fault is cleared, the original network conditions again exist. Determine the critical clearing angle and critical clearing time. (Roll=PQRS)
Q2. The single-line diagram of a simple three-bus power system is shown in Figure-2. Each generator is represented by an emf behind the sub-transient reactance. All impedances are expressed in per unit on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A three-phase fault occurs at bus 3 through a fault impedance of Zf = j0.19 per unit. (i) Using Th'evenin's theorem, obtain the impedance to the point of fault and the fault current in (ii) Determine the bus voltages per unit. ) j0.05 j0.075 j0.75 2 j0.30 j0.45 Figure-2: Single line diagram of the power system network for Q2 3
The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of an unloaded synchronous machine decreases from a high initial value to a lower steady-state value, going periods through the stages of __________ and ________ periods.
A generator feeds power to an infinite bus through a double circuit transmission line. A3 phase fault occurs at the middle point of one of the lines. The infinite bus voltage is 1 pu, the transient internal voltage of the generator is 1.1 pu and the equivalent transfer admittance during fault is 0.8 pu. The 100 MVA generator has an inertia constant of 5MJ/MVA and it was delivering 1.0 pu power prior of the fault with rotor power angle of 30 °. The system frequency is 50 Hz. The initial accelerating power (in pu) will be
The one line diagram of a simple three bus power system is shown in figure Each generator is represented by an emf behind the subtraction reactance. All impedances are expressed in per unit on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. Athree phase fault occurs at bus 3 through a fault impedance of Zf=j0.19 per unit. a-using thevenin’s theorem obtain the impedance to the point of fault and the fault current in per unit. b-determine the bus voltage and line currents during fault
two alternators A and B having 5% speed regulation are working in parallel at a station. Alternator A is rated at 15 MW while B is at 20 MW. When the total load to be shared is 12 MW, then how much of the load will be shared by the alternator B?
Q-5-) 60 Hz generator supplies 0.50 Pmax power to a busbar with infinite power over a conveying line. When a fault occurs, the reactance value between the generator and the infinite bus becomes 400% times the value before the fault. When the fault is isolated, the maximum power that can be transferred generator to the endless bus is 75% of the original (initial) maximum value. Accordingly, using t area criterion method, calculate the critical clearance angle of the system. 00
A generator feeds power to an infinite bus through a double circuit transmission line. A 3 phase fault occurs at the middle point of one of the lines. The infinite bus voltage is 1 pu, the transient internal voltage of the generator is 1.1 pu and the equivalent transfer admittance during fault is 0.8 p.u. The 100 MVA generator has an inertia constant of 5mJ/MVA and it was delivering 1.0 p.u. power prior of the fault with rotor power angle of 30°. The system frequency is 50 Hz. If the initial accelerating power is X pu, the initial acceleration in elect dag / sec, and the inertia constant in MJ - sec / elect deg respectively will be
G1 Bus 1 Bus 2 Line Bus 3 T2 Bus4 M1 j402 25 MVA Ye A 13.0 kV Xg1 =10% зо мVA 13.4/69 kV 20 MVA 66/13.2 kV 15 MVA 13.0 kV Xmi =15% 10% 10% e direct-axis subtransient reactances of the synchronous generator and otor are given above in the figure. The fault impedance (ZA) is 15.87 ohm ie generating is operating 25 MVA, 0.95 p.f. lagging, and at 10% above rate Itage when a three-phase fault occurs at bus 1. Determine each three-phase ult
The one-line diagram of a simple power system is shown in Figure below. The neutral of each generator is grounded through a current-limiting reactor of 0.25/3 per unit on a 100-MVA base. The system data expressed in per unit on a common 100-MVA base is tabulated below. The generators are running on no-load at their rated voltage and rated frequency with their emfs in phase. G Stark Item Base MVA Voltage Rating X' x² 20 kV 20 kV 20/220 kV 20/220 kV 100 0.05 0.15 0.15 0.10 0.10 220 kV 0.125 0.125 0.30 0.15 0.25 025 0.7125 0.15 100 100 0.15 0.05 0.10 0.10 0.10 100 0.10 100 100 Lu La 220 kV 0.15 220 kV 0.35 100 A balanced three-phase fault at bus 3 through a fault impedance Zf= jo.I per unit. The magnitude of the fault current in amperes in phase b for this fault is: Select one: A. 345.3 B. 820.1 C. 312500 3888888 产产

A synchronous generator is feeding its rated power of 250 MW to a large 60 Hz network over a double circuit transmission The maximum steady state power that can be transmitted over the line with both circuits in service is 500 MW and is 350 MW with any one out of service. A solid three-phase fault occurring at the network-end of one of the lines causes it to trip. If inertia constant is H = 3.5 s, calculate the critical clearing angle and critical clearing time in which the circuit breakers must trip so that synchronism is preserved.
b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (1) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.