The steel reinforced concrete slab shown in Fig. Q3 below has a 200mm thickness and is supported by 3 concrete beam girders at equal spacing of 9m. The deck is monolithically attached to the girders and has a total length of 20m and a width of 10m. It is reinforced with 15 x q16 steel bars across the length (19m length each bar) and 10 x p16 steel bars across the width (9m each bar). C 9 m Fig. Q3 0 Assuming a nominal concrete unit weight of 25kN/m' and a steel unit weight of 78kN/m, calculate the dead load G in kN. Consider only the deck selfweight and the selfweight of the steel reinforcement. Neglect the concrete beam girders. The concrete deck carries a live load Q of 6kN/m Determine the total design load of the deck for the ultimate (ULS) and serviceability limit states (SLS) in kN (neglect the beam girders). A steel column is 4m long and has a diameter of 0.50m. It is subjected to a compressive force of 20MN. Given that the, elastic modulus of the material is 210GPA, calculate the value of compressive stress (in N/m'), compressive strain and the shortening o in mm of the column. Assume buckling effects may be ignored as the column is considered stocky.

The steel reinforced concrete slab shown in Fig. Q3 below has a 200mm thickness and is supported by 3 concrete beam girders at equal spacing of 9m. The deck is monolithically attached to the girders and has a total length of 20m and a width of 10m. It is reinforced with 15 x q16 steel bars across the length (19m length each bar) and 10 x p16 steel bars across the width (9m each bar). C 9 m Fig. Q3 0 Assuming a nominal concrete unit weight of 25kN/m' and a steel unit weight of 78kN/m, calculate the dead load G in kN. Consider only the deck selfweight and the selfweight of the steel reinforcement. Neglect the concrete beam girders. The concrete deck carries a live load Q of 6kN/m Determine the total design load of the deck for the ultimate (ULS) and serviceability limit states (SLS) in kN (neglect the beam girders). A steel column is 4m long and has a diameter of 0.50m. It is subjected to a compressive force of 20MN. Given that the, elastic modulus of the material is 210GPA, calculate the value of compressive stress (in N/m'), compressive strain and the shortening o in mm of the column. Assume buckling effects may be ignored as the column is considered stocky.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

H. W.: Determine approximately the force in each member of the truss shown in Fig. below. Assume that (1) Diagonals can support both tensile and compressive forces. (2) Diagonals cannot support a compressive force. 5 kN Jo A 1 B 609 10 kN H C 4@3m-12 m D 5 kN E 4 m
A concrete floor slab measuring 6 m x 3 m is simply supported on one side brick load bearing walls along the 6 m sides. The concrete slab is 200 mm thick and reinforced at the bottom as follows.1. Main reinforcement (short span i.e the bars are parallel to the short span), Y 12, shape code 34 @ 125 mm centre to centre,2. Distribution reinforcement (long span i.e the bars are parallel to the long span), Y 10, shape code 20 @ 300 mm centre to centre,3. Concrete cover, 30mm,4. Concrete strength, 40MPa.Draw the reinforcement layout for this slab, in plan and section, indicating all the reinforcement and necessary information required by the contractor. You must calculate and indicate the number of bars required on your drawing. You do not need to calculate the bar lengths and the curtailment. Your drawing must be neat.
14 в 5m 5 m 5 m 5 m 5 m A 5 m 5 m E 30 kN 20 kN From the given truss, which member has an internal force of 34.6 kN COMPRESSION ? O AC CD BC BD
Question 7 of 10 Current Attempt in Progress A N 14 KN L F 19 KN O M K 6 panels at 5 m 42 G 26 KN H J 21 KN 30° I 0/10 14 KN
50 kN 50 kN 100 kN Sm 4m 3m From the given truss, which member has an internal force of 50 kN COMPRESSION ? AD AC CD BD
How many Zero force members are there in the truss shown? В D F E A K H[100 kN 60 kN LL 60 kN O 2 O 3 5 O 7
The section of a Super-T prestressed concrete girder is shown below. The girder is simply supported on a span of 7.0 m and are pre-tensioned with total initial force of 825 kN from low-relaxation strands. The girder supports a total dead load of 2 kPa and live load of 6 kPa. There is a loss of prestress of 0.2 at service loads. Assume "-" for compression and "+" for tension. Hint: Assume tributary width is equal to flange width. Properties of the section: A = 100,000 mm2 INA = 940 x 106 mm4 All measurements in the drawings are in millimeters. 1. What is the stress, in MPa, at the top fibers of the girder at end span due to initial prestressing force only? 2. What is the stress, in MPa, at the bottom fibers of the girder at midspan due to initial prestressing force only? 3. What is the stress, in MPa, at the top fibers of the girder at end span due to prestressing force and service loads? 4. What is the stress, in MPa, at the bottom fibers of the girder at midspan due to prestressing…
When the columns at E and H of the floor framing plan shown are deleted, girder BEHK becomes one span fixed ended beam supporting beam DEF at E and beam GHI at H.The following loads on girder BEHK are as follows: Concentrated load at E = 277 kN Concentrated load at H = 266 kN Uniform load throughout its length = 8 kN/m 2.5 m 2.0 m 2.0 m A D G 6m B E H K 6m C F Calculate the maximum positive moment (kN.m) due to the uniformly distributed load only. (TWO DECIMAL PLACES)
Problem 8.4 Distributed Loads The framing system shown in the figure is subjected to a 7.7 kN point load and triangular distributed load with a maximum magnitude of 9.5 kN/m. You are required to: a) Determine the reaction forces at the Pin D. b) Determine the reaction forces at Pin A. c) Determine the force in the member AC. 7.7 kN B 2.5 m STENDER EERSTE CONNECTION SEAN BUTER PLATING 3.5 m D INNER BOTTOM PLATING TRANSVERSE LONGITUDINAL STRAKE 9.5 kN/m 5 m
Determine the unity check ratio for the member GF of the truss shown below (Per API RP-2A code provisions). Joints of the truss are frictionless joints and the forces in the truss members are axial forces only. 20 kip Member GF (Hollow circular cross section): Outer diameter = 10" 30 kip 30 kip 30° Wall thickness = 0.25" Ey = 50 ksi 300 E 60° 60° 30° K=1.0 A, 30 60° 60° 30° 30 D. 4ft 4ft 4ft Ay [Hint: Axial Force in member GF = 50 kips (axial compression)]
Determine the stress in members BD, DE and EG of the truss shown if the diameter of each cross-section is equal to 2.5cm. State whether each member is in tension or compression. SEN オ DI 4.5m Match each item to a choice: OEG OBD ODE
For a roof truss system of an industrial building, following data is given Span of truss = 6.0 m Spacing of truss = 3.0 m centre to centre Inclination of roof 30° Spacing of purlins = 2.0 m centre to centre Wind pressure = 1.5 kN/m² Roof coverage -A.C. sheets weighing 200 N/m2 %3D %3D Design: (i) channel section purlins.