the source voltage is 240√2 sin (2 50t) V, R = 10 ohms, and L = 50 mH. Calculate 1- the average freewheels diode current, hence average rectifier diode current 2- the rms load current, hence load power and supply rms current 3- the supply power factor. iDI lo D₂ iD2 R D₁

the source voltage is 240√2 sin (2 50t) V, R = 10 ohms, and L = 50 mH. Calculate 1- the average freewheels diode current, hence average rectifier diode current 2- the rms load current, hence load power and supply rms current 3- the supply power factor. iDI lo D₂ iD2 R D₁

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Find the magnetic field intensity on a magnetic field

Q: Enumerate the steps in making a power supply

A: Assuming that you are asking for the design of laboratory DC power supplies.

Q: 1-1-Find the propagating E and H fields for the given Coax Line in Fig.1.Determine voltage and…

A: COAXIAL CABLE : Coaxial cable is a single-ended transmission medium, meaning that the signal current…

Q: .What is the magnitude of the impedance of a 14 μF capacitor? Assume the frequency is 217 Hz .Write…

Q: Q3/ Determine the centre frequency, maximum gain, bandwidth and type filter for the circuiting…

A: Given data High pass frequency: The value of the capacitor is 0.047μF The value of the resistance is…

Q: A 220 V self-excited shunt motor has armature and field resistances of 0.2 Ω and 220 Ω respectively.…

A: In this question we need to find a new speed in rpm (rev/min) if an external armature resistance of…

Q: 2. The volume in spherical coordinates described by r <a [m] contains a uniform volume charge…

Q: I. From the given block diagram below, find the following: a) the total output of the system. b) the…

A: Various nodes are marked with different letters inorder to decrease the simplification.

Q: 2. Determine the current flowing in R₁, R₂, R3, R4, Rs and V₁. (if Voltage drop across R,=20 V).…

A: The required parameters can be calculated by using the ohms law, kirchhoff's current law and voltage…

Q: 1. Given the potential field V = 80r²cose, and a point P (2.5, 0 = 30°, p = 30°) in free space.…

A: As per guidelines given to us we can only provide the solution of one question in multiple type of…

Q: Μ 3 R4 1ΜΩ V1 4 18V R2 2ΚΩ Q1 F 2 1 R3 Ο 0.51kΩ

Q: 70. A circuit supplies a continuous load of 38 amperes and is protected by a 50-amperecircuit…

A: While calculating the conductor size for a continuous load, take 125% of overloading conditions…

Q: Vse mesh analysis 2 4. + $5 34 Toy 50x to solve for i at 5.

A: We need to find out the current for given circuit

Q: V ΤΟ 20 Ω Μ j10 Ω Μ 40 Ω j30 Ω Ξ 30 Ω Μ j60 Ω

Q: (no+23), = (abcdefg), ABCD F 0000 X 0001 a 0010 b 0011 с 0100 0101 0110 0111 1000 1001 g 1010 f 1011…

A: Given data, Number (n)=47 (n+23)10=(abcdefg)2

Q: 3 Find the total power consumed by the circuit 2 50 A 4

Q: 10 ΜΩ , 6.8 ΜΩ , 24 V VGSQ • 2.2 ΚΩ IDQ VGs Th) = 3 V ID(on) = 5 mA VGS(on) = 6 V • 0.75 ΚΩ

A: given here a mosfet circuit and asked to find the VGSQ , IDQ , VDS , VD , VS .

Q: Given v₁ = 20sin(wt +60-) and v2 = 60cos(wt -10-), determine the phase angle between the two…

A: Given data, V1=20sinωt+60° VV2=60cosωt-10° V

Q: design a 3-phase 50Hz inverter

A: Types of converters Rectifiers ( AC to DC Converter ) Chopper ( DC to DC Converter) Inverter ( DC…

Q: What is the magnitude of the impedance of a 35 Ohm resistor? Assume the frequency is 180 Hz .Write…

A: Given, Resistance, R = 35 ohm Frequency, f = 180 Hz

Q: QUESTION 4 Consider the periodic signal y(t) of Figure Q4(a) a. What are the Fourier series…

A: Fourier series is a mathematical representation used to obtain the solution of complex functions

Q: 23/A- For the circuit shown in figure 3 draw the output voltage waveform across the SCR and the…

A: Silicon controlled rectifier: The SCR is a semiconductor devise its a belong three-terminal…

Q: C. Find the Fourier transform of f(t) = 28 (t + 2) - 28(1-2).

Q: How do you identify the anode of an unmarked diode? When the forward current of a diode increases,…

A: In this question we will solve diode related problems.... Note :- as per our guidelines , I am…

Q: A circuit element has an impedance of 142-51° mo when the frequency is 175 Hz. What is the…

Q: A 3-phase 440V, wye connected induction motor has a star-connected stator and delta connected rotor…

Q: Find v(1) in the circuit of Fig. 16.4, assuming zero initial conditions. 552 192 www www u(1) IH%(1)…

Q: A balanced delta-connected load with impedance per phase of 30230° 2 is connected to an abc-sequence…

A: It is given that: Z∆=30∠30° ΩeAC=-1202cos120πt-π6 V

Q: 1.2 The prefix micro stands for: (a) 106 (b) 10³ (c) 10-3 (d) 10-6

Q: 8210° +62-20° and express the result in rectangular form. 9280°-4250° Evaluate O 0.50 +j2.24 O…

Q: A non-magnetic circuit has a reluctance of 38.6 gilbert per maxwell. Calculate how much flux will be…

A: Here the concept & the calculations related to the magnetic circuit. Given :- Reluctance R=38.6…

Q: et Ē(x,y,z) = 2x²î +5yj+3zk. The value of f(-E)dv, where V is the volume V enclosed by the unit cube…

Q: slation:- V. (s) - LO [1/10 BY Vo(s) Vo(s) KCL 1 10 [ 5+2] Vo(s) How? Vo (s) LO S+) + Vo (s) Lo 11…

Q: Determine the y-parameters of the network in figure 5?

Q: Which of the following is the least likely component to be used in making a power supply? resistor…

A: Option A Resistors Because resistors associate with power loss and voltage drops. Both are not…

Q: Thevenin impedance of a source is 41+j61 Ohms, and the Thevenin voltage 195 + j43 V. Find the value…

Q: The load of an industrial plant consists of 600kVA at a power factor of 0.75 lag. One large motor is…

A: In this question , we will find new load in kVA if motor is to be added in parallel to load....

Q: A resistance of 12 ohms and capacitance of 0.01 farad is connected in series with a 200 volts…

Q: The property of conductance is the a. opposition to current flow b. ease of voltage flow c.…

A: 1) conductance is the opposite of resistance. it is calculated as the reciprocal of resistance.…

Q: Determine the z-transform and ROC of the given signal: -n x(n) = (G) u(−n)-n-5^u(−n − 1) + 2^(n

Q: Determine the z parameters for the circuit shown in below. 6Ω 5Ω ww + 4Ω V₂ 16 0.66V,

A: Z- parameter is used in two port network. Z- parameter analysis the power distribution networks…

Q: A. Find the following requirements in plotting the root locus. • number of branches • number of…

A: For the given unity feedback control system calculation of : A. Find the following requirements in…

Q: Assuming that there are no charges in the four regions shown in the figure, which of the patterns…

A: The electric field lines originate at a positive charge and terminate at a negative charge. In…

Q: Q4) let V (cos 20)/r in free space; find the volume charge density at point. A(0.5,60°,1).

A: In this question we will find volume charge density from potential....

Q: PROBLEM: in plotting root locus, find the asymptote line angle is/are. R(S) K s(s+ 1)(s² + 4s +13)…

A: Brief description: For the given closed loop transfer function we need to calculate asymptote line…

Q: for square wave PWM inverter, Vdc=100V, L=25mH, R=1002, f-60Hz. draw the spectrum of the output…

A: Square wave inverter is convert the solar DC to AC power. it is a simple to design and high…

Q: X(z) 2z-1 1-3z1+z-² + 5z-3

Q: 50 V 50 www α b 20 Ω

Q: So how many hour does the 2 batteries will work on 6watts led light

Q: The phase angle of 12cos(5t - 30-) O 12°, lagging O 12°, leading 30°, lagging O 30°, leading

A: given that 12cos(5t-30) convert it into polar form 12<-30°

Question

the source voltage is 240√2 sin (2 50t) V, R = 10 ohms, and L = 50 mH.
Calculate
1- the average freewheels diode current, hence average rectifier diode
current
2- the rms load current, hence load power and supply rms current
3- the supply power factor.
iDI
io
D₁
D₂.
ip2
R
+

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
The ripple factor for pure dc is Answer: For the given circuit below, it operates on a peak-to-peak input voltage of 390.1 V, F= 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1, D2 AC Input Vsec (Source) .03 D4 Load O 27.31 O 18.11 O 13.93 O 20.91
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
P) For single - phase half-controlled bridge rectifier shown in the figure: 1. Derive a formula for mean load Voltage. 2. Draw the waveforms of Ve,is,iz, i3, iy and io assuming highly inductive Load and =45. T. T3 Dy
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
In the figure given we have u(t)=10. cosot [V]. We assume the diodes and the A-meter (A) to be ideal. A u(t) a) Plot the waveform of the current flowing through the A-m in scale. b) What is the reading of the A-m, if it is moving-coil type? c) What is the reading of the A-m, if it is moving-iron type? d) Calculate the power factor of the WHOLE structure. R1 1 R2 102
Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter connected with D1 indicates 8 A r.m.s current, and the source frequency is 50 Hz Due to system inductance the average voltage drops to 96.2% of idealized value ( when the inductance is neglected). How much will the average and r.m.s voltage s be? The r.m.s phase current and average load current Is=? & Idc=? The secondary r.m.s voltage and transformer capacity Vs & KVA? The inductances causes the voltage drop Lc=? The diode forward current and maximum inverse voltage? Now, if the phase B is failed ( disconnected), how much with new dc voltage be in %..Vdc=….% ??
For the given circuit below, a step down transformer gives an RMS voitage of 230 V/ 12-0-12 V with a load resistance of 22 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. O 33.94 O 26.83 O 16.97 O 21.17 A silicon diode in a half-wave rectifier has a barrier potential of 0.7 V. This has the effect of reducing the peak input voltage by 0.7 V. increasing the peak input voltage by 0.7v. no effect. increasing the peak output voltage by 0.7 V. Next nane
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%