The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. www A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. www www wwwwwww www w m w www w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW d A D B E

The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. www A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. www www wwwwwww www w m w www w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW d A D B E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

45. A geared turbine unit delivers 18,500 kW at the bull gear coupling at full power with a propeller shaft speed of 400rpm. Under these conditions, the mechanical losses total 925 kW. At 35 km/hr, the propeller makes 200 rpm and the shaft power is 2000 kW. Assume the mechanical losses vary as the square of the rpm and find the estimated mechanical loss power at 35 km/hr. A. 321 kW B. 231 kW C. 124 kW D. 432 kW
A group of first year students are designing gear reduction system in the Makerspace, consisting of four gears A, B, C and D. The radii of the gears are TA = 1.5 in, r = 3.5 in, rc = 2.0 in and r₁= 5.0 in. Gear A rotates clockwise with a constant angular velocity WA = 440 rpm. Gears B and C are rotating together on the same shaft. Determine: @A A B rc C D TA TB "D (a) the angular velocities of gears B and D, (b) the accelerations of the contact point on gear B and contact point on gear D.
80 Design a two-speed gearbox suitable to transmit 25kW. The input shaft runs at 630rpm and carries two gears, A and B. The 2nd shaft carries two sliding gears, C and D. Gear C meshes with gear A, giving the driven shaft a speed of approximately 315rpm. Gear D meshes with B giving the driven shaft a speed of approximately 215rprn. The distance between the centres of the shafis is approximately 270mm and the teeth are 20° full depth involute. Using a module of 6mm and basic stress of 120MPa for all the gears, apply the Lewis formula and calculate: No of teeth for each gear [30;23;60,67] PCD for each gear [180; 138,360;402)mm True speed of gears C and D [216;27] Correct centre distance between the shafts (270) Width of the tooth material for each gear if [A&C:47mmm; B&D:53mm] the basic stress is 120MPa, using the Lewis formula. a) b) d) e) f)
8. An epicyclic gear train, as shown in Fig. 13.37, has a sun wheel S of 30 teeth and two planet wheels P-Pof 50 teeth. The planet wheels mesh with the internal teeth of a fixed annulus A. The driving shaft carrying the sunwheel, transmits 4 kW at 300 r.p.m. The driven shaft is connected to an arm which carries the planet wheels. Determine the speed of the driven shaft and the torque transmitted, if the overall efficiency is 95%. [Ans. 56.3 r.p.m.; 644.5 N-m] Arm fo --- Fig. 13.37 S A P P An opiquello reduction cong ng chown in Fig 12 20 ho naft & fund orm 12. The nem hon o pin
An electric motor develops 8 HP at 2652 rpm. An 19 tooth gear is fitted to its output shaft to drive a gear on an output shaft. How many teeth would be needed on this output gear if an output torque of 92 Nm is required? Answer: Next page page Finis Time 9Type here to search
A steel shaft transmits 50 Bhp at 1400 rpm. Find the torque in in-lb.
Assignent no 1 Qt+ A Compound gear 6 Jears. No of teeth; train Consists of A B D 60 40 35 २४ 50 30 shaft on another shaft. The Gears B ş C are on one while are gears Gear A drives c drives gear D B, gear gear S gear E drives gear F. Gear A transmits 1.5 Kw at 15orpm Find speed of Gear F ? Q2+ State advatages of Cycloidal In volute profile as a gear tooth pnfile.
Please solve ellaborately using the equation provided in the figure and include the untis in every step, show diagram and write your solutions clearly and readable if your solution is in written form. Your work will be appreaciated much. Thank You. Two shafts, 1.67 ft apart, are connected by an open belt. The input shaft has a speed of 350 rpm and the output shaft should be capable of running at speeds of 950 rpm, 650 rpm, 450 rpm, 250 rpm, and 150 rpm. If the diameter of the smallest pulley on the driven shaft is 2 inches, calculate the length of the belt and the diameters of each pulleys attached at the shafts.
You have been asked by your engineering company to design a complete gear and shaft system shaft that is made of steel. The solid shaft is linked with gear A, B. C and D with gear A., B and C produces torque of 15 kNm (clockwise), 30 kNm (clockwise) and 75kNm (anticlockwise). respectively each. If AB = 0.70m, BC= 0.80 m and CD=0.90 m with the shafts consist of solid circular shafts with a diameter of 150 mm having the shear modulus of G = 80 GPa, b) The shafts are now to be redesigned by drilling only through shaft BC with a diameter hole, cz to produce a hollow shaft BC. It is also known that the allowable shear stress, Tall in the shaft must not exceed 85 MPa. i) Determine the minimum wall thickness of the shaft BC, tBc
what is the polar moment of inertia (in^4) of a solid shaft that has a torque of 2Kn-m and a stress of 30MPa?
a steam engine runs at 150rpm. its turning moment diagram gave the areas in mm2 taken in order above and below the mean torque line is 500,250,270,390,190,340,270,250, the scale for turning moment is 1mm=500mnm, 1mm=5’ if the fluctuation of speed is not to exceed +or-1.5% of mean, determine a suitable diameter and cross-section of the rim of flywheel with axial dimension equal to 1.5times the radial dimension. the hoop stress is limited to 3mpa and the density of material of flywheel is 7500kg/m3.
For the steel shaft shown in Fig. Draw a torque diagram for the shaft. 8 kN-m 15 kN-m 6 kN-m GGGGG T 14 kN-m