The shaft shown in the figure below is to be machined on a lathe from a Ø 25mm bar. Calculate the machining time if speed V is 60 m/min., turning feed is 0.2mm/rev, drilling feed is 0.08 mm/rev and knurling feed is 0.3 mm/rev. 20 $ 25 $10 25 10 45 Fig 1. Sectional view of workpiece

The shaft shown in the figure below is to be machined on a lathe from a Ø 25mm bar. Calculate the machining time if speed V is 60 m/min., turning feed is 0.2mm/rev, drilling feed is 0.08 mm/rev and knurling feed is 0.3 mm/rev. 20 $ 25 $10 25 10 45 Fig 1. Sectional view of workpiece

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The shaft shown in the figure below is to be machined on a lathe from a Ø 25mm bar. Calculate the machining time if speed V is 60 m/min., turning feed is 0.2mm/rev, drilling feed is 0.08 mm/rev and knurling feed is 0.3 mm/rev?
Note: All dimensions are in mm Ø 34 3.) A 34 mm diameter x 120 mm shafting will be turned using a lathe to produce a step shafting as shown in the figure. Calculate the required (minimum) total machining time Tm with the following cutting Ø 30 50 120 conditions: Step Shafting Rough Turn: V = 30 m/min; Max. Depth of Cut = 1.5 mm; Feed = 0.2 mm/rev Finish Turn: V = 60 m/min; Max. Depth of Cut = 0.5 mm; Feed = 0.05 mm/rev Lathe available rpm: 150, 200, 250, 350, 400, 450, 500, 550, 600, 650, 700
Note: All dimensions are in mm Ø 34 A 34 mm diameter x 120 mm shafting will be turned using a lathe to produce a step shafting as shown in the figure. Calculate the required (minimum) total machining time Tm with the following cutting 30 -70- 50 120 conditions: Step Shafting Rough Turn: V = 30 m/min; Max. Depth of Cut = 1.5 mm; Feed = 0.2 mm/rev Finish Turn: V = 60 m/min; Max. Depth of Cut = 0.5 mm; Feed = 0.05 mm/rev Lathe available rpm: 150, 200, 250, 350, 400, 450, 500, 550, 600, 650, 700
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 47 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Total time required to complete the turning operation is 59.6 minutes (a) Find number of passes to finish the entire turning operation ( (b) The actual length of the turning operation in mm ('
A mild steel specimen of Initial diameter of 53.5 mm is turned to final diameter of 49 mm for an initial length of 151 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.2 mm/rev & Depth of cut is 0.5 mm (ii) During machining the tool's approach length is 7 mm, over run length is 4mm (iii) Total time required to complete the turning operation is 52.6 minutes (a) Find number of passes to finish the entire turning operation (b) The actual length of the turning operation in mm (c)The time required to complete one single turning operation in minutes (d) Spindle speed in rpm
A mild steel specimen of Initial diameter of 32.5 mm is turned to final diameter of 25 mm for an initial length of 154 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.3 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 6 mm, over run length is 3mm (iii) Time required to complete one single turning operation is 2.3 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes (c) Spindle speed in in rpm (d) Cutting speed in m/minutes
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (a)Find number of passes to finish the entire turning operation (b) Total time required to complete the turning operation in minutes
A mild steel specimen of Initial diameter of 30.5 mm is turned to final diameter of 27 mm for an initial length of 153 mm on a lathe machine. Using the given data find the following. (i) Feed of 0.4 mm/rev & Depth of cut is 0.5 mm (ii)During machining the tool's approach length is 5 mm, over run length is 2mm (iii) Time required to complete one single turning operation is 3.5 minutes (c) Spindle speed in in rpm (= (d) Cutting speed in m/minutes(=
The end of a large tubular workpart is to be faced on a NC vertical boring mill. The part has an outside diameter of 38.0 in and an inside diameter of 24.0 in. If the facing operation is performed at a rotational speed of 40.0 rev/min, feed of 0.015 in/rev, and depth of cut of 0.180 in, determine (a) the cutting time to complete the facing operation and the cutting speeds and metal removal rates at the beginning and end of the cut.
The outline of the part in figure below is to be profile milled, using a 20 mm diameter end mill with two teeth. The part is 10 mm thick. Cutting speed =125 m/min and feed = 0.10 mm/rev. Use the lower left comer of the part as the origin in the x-y axis system. The two holes in the part have already been drilled and will be used for clamping the part during milling, Write the part program in the APT format.
A twin-spindle drill simultaneously drills one ½-in hole and one ¾" through a 1" wide work piece. Both holes are twist drill with 118° point angles. cutting speed for material is 230 ft/min. The rotation speed of each spindle can be configured individually. The feed rate of both holes must be set to the same value, since both spindles go down at the same speed. The forward speed is set in such a way that the speed total metal removal does not exceed 1.50 in3 /min. Determine: a) the velocity maximum feedrate (in/min) that can be used, b) the individual feedrates (in/rev) that result in each hole and c) the time required to drill the holes.