The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 325 psi, determine the magnitude of the shear stress parallel to the weld.

The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 325 psi, determine the magnitude of the shear stress parallel to the weld.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 236 psi, determine the magnitude of the shear stress parallel to the weld. 55°A O 4.44 ksi O 6.20 ksi O 5.71 ksi O 3.71 ksi O 4.02 ksi
The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 700 mm and a wall thickness of 9.5 mm. For a gage pressure of 0.83 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume β=32∘
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 60 in. and a wall thickness of 0.375 in. For a gage pressure of 131 psi, determine the normal stress perpendicular to the weld.
The cylindrical portion of the compressed air tank shown is fabricated of 0.25-in.-thick plate welded along a helix forming an angle β= 30° with the horizontal. Knowing that the allowable stress normal to the weld is 10.5 ksi, determine the largest gage pressure that can be used in the tank
The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 770 mm and a wall thickness of 10.7 mm. For a gage pressure of 1.21 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume ß = 56'. %3D Answers: (a) Normal stress- MPa (b) Shear stress- MPа
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 2.56 ksi. 55° O 213 psi O 200 psi O 184 psi O 170 psi O 107 psi
What is the axial stress in the bronze rod (in MPa)? 2m 3m 60 kN IS mm banzerod
H.W.6: A hollow circular cold-rolled bronze [G, = 6,500 ksi] tube (1) with an outside diameter of 1.75 in. and an inside diam- eter of 1.25 in. is securely bonded to a solid 1.25-in.-diameter cold-rolled stainless steel [G2 = 12,500 ksi] core (2) as shown in Figure and the allowable shear stress of core (2) is 60 ksi. Determine . The allowable shear stress of tube (1) is 27 ksi, (a) the allowable torque T that can be applied to the tube-and- core assembly. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced in a 10-in. length of the assembly by the allowable torque T. (1) т. FIGURE
Calculate the normal stress in the weld due to axial force of 40 kN. Consider throat thickness of the weld is 4.2 mm and effective length of the weld is 350 mm a. 15.66 N/mm? b. 27.21 N/mm? c. 33.32 N/mm? d. 41.42 N/mm²
H.W.6: A hollow circular cold-rolled bronze [G, = 6,500 ksi] tube (1) with an outside diameter of 1.75 in. and an inside diam- eter of 1.25 in. is securely bonded to a solid 1.25-in.-diameter cold-rolled stainless steel [G, = 12,500 ksi] core (2) as shown in Figure and the allowable shear stress of core (2) is 60 ksi. Determine . The allowable shear stress of tube (1) is 27 ksi, (a) the allowable torque T that can be applied to the tube-and- core assembly. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced in a 10-in. length of the assembly by the allowable torque T. (1) FIGURE
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 26 ksi.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 16 ksi. O 480 psi O 305 psi O 376 psi O 407 psi 523 psi