The power P required for operating a pump depends on the diameter of the pump D, the pressure rise Ap across the pump, the fluid density p, the fluid viscosity and the volume flow rate Q through the pump. Using Buckingham's 7 Theorem, and D, Q and p as the repeating variables, the dimensionless TT group associated with is given by DaQbp. Determine the values of a, b and c. 1. [0.99, 1.01 2. [-1.01, 0.99 3. [-1.01, -0.99 a= b= C=

The power P required for operating a pump depends on the diameter of the pump D, the pressure rise Ap across the pump, the fluid density p, the fluid viscosity and the volume flow rate Q through the pump. Using Buckingham's 7 Theorem, and D, Q and p as the repeating variables, the dimensionless TT group associated with is given by DaQbp. Determine the values of a, b and c. 1. [0.99, 1.01 2. [-1.01, 0.99 3. [-1.01, -0.99 a= b= C=

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

The friction in flows through the pipe is defined by a dimensionless number called the fanning friction factor (f). The Fanning friction factor is represented by another dimensionless number, the Reynolds number (Re).It depends on the diameter of the pipe and some parameters related to the fluid. An equation that can predict f given the Reynolds number is given as follows. If Re =4000, e/D=0.01 in this equation, find the value of f using the Simple Iteration method by taking f0=0.1 as the initial value for the solution (ԑ=0.0001)
02: The power input P to a centrifugal pump is assumed to be a function of the volume flow Q, impeller diameter D, rotational rate 2, and the density p and viscosity u of the fluid. Rewrite these variables as a dimensionless relationship. Hint: Take 2, p, and D as repeating variables.
Water X 50-mm inside diameter The volume flow rate of the system The pressure at the point "A" The pressure at the point "B" 25-mm diameter As a consultant at one of the country's leading soft drink companies, you are tasked with evaluating the system depicted to determine the following parameters using Bernoulli's Equation if the values assigned to "X" and "Y" are 3m and 0.5m respectively: i. ii. iii.
The conduction heat transfer in an extended surface, known as a fin, yields the following equation for the temperature T, if the temperature distribution is assumed to be one-dimensional in x, where x is the distance from the base of the fin, as shown in figure: To Fin >X T(x) h,T Heat Loss d²T_hp (T-T) = 0 dx² ΚΑ dT dx = 0 Here, p is the perimeter of the fin, being 2R for a cylindrical fin of radius R; A is the cross-sectional area, being R2 for a cylindrical fin; k is the At x = 0: T = T₁ dT At x=L: :0 dx thermal conductivity of the material; T is the ambient fluid temperature; and h in the convective heat transfer coefficient. The boundary conditions are as follows: where L is the length of the fin. Solve this equation to obtain 7(x) by using Euler's method for R=1cm, h= 20 W/m².K, k = 15 W/m-K, L = 25 cm, T₁ = 80°C, and T = 20°C.
20 The efficiency of a fan depends on the density p, the dynamic viscosity μ of the fluid, the angular velocity , diameter D of the rotor and the discharge Q. Express n in terms of dimensionless parameters.
. I am planning to perform some volume-flow rate measurements in the Fluid Mechanics Laboratory. For this, I need a volumetric measuring tank (graduated cylinder) and a stopwatch. I considered the volume of the measured tank as 15 gallons and a stopwatch with reaction time as 1/10th of a second (though resolution of 1/1000th of a second). What is the volume flow rate if it takes 5 minutes to fill a 15-gallon of tank? Determine the smallest division to be on the tank in order to estimate the volume flow rate within an accuracy of ± 0.05 gpm.
A cart weighing 0.5 kg is drawn up a smooth 45° incline by a motor, M, winding up a cable. The force in the cable can be expressed as 5t² N, where t is in seconds. When t = 0, the displacement s = 0 and the initial velocity is 3 m/s. Find the cart's velocity when t = 2 seconds. > Draw a very clear FBD of the cart that you can use to write the equations of motion > Write the equations governing the cart's motion along the incline. Use axes parallel and perpendicular to the incline. Find the velocity requested
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.
Measurements at a certain point of a pipe have been done where the following parameters were recorded: Fluid of density = 887 kg/m3, Fluid velocity = 4 m/s, Pressure= 11.3 KN/m2 If the total energy per unit weight at this point = 32 m, then the potential energy is: O Zero m 10 m 20 m 30 m &
Ql: The viscosity in industrial measurement continue to use the CGS system of Lunits, since centimeters and grams vield convenient numbers for many fluids. The absolute viscosity () unit is the poise, I poise = 1 gtem. s). The kinematic viscosity (v) unit is the stohes, I stokes = 1 em /s. Water at 20C has u = 001 poise and also V= 0.01 stokes. Express these resalts in (a) SI and (h) BG tanits.
1. Start from the following equations from class notes (treat as given): The shear stress in pipe flow T = -μ- dr du 16 [1-(-)²), AP D² 16μL The fluid velocity in the pipe u = Derive clearly the following results: (a) The shear stress on the wall of the pipe, Tw. (b) The average velocity in the pipe flow, ū. (c) The Darcy friction factor, defined by f where L is the length of the pipe. 8 tw pū² (d) Express the result of (c) in terms of the Reynolds number, Re. (e) Find an expression for the head loss due to shear stress at the wall, AH₁, in terms of f,u, D and L. (f) What are the main assumptions in the fluid flow, in order to analyse the flow in this way?
02: The power input P to a centrifugal pump is assumed to be a function of the volume flow Q, impeller diameter D, rotational rate N, and the density p and viscosity u of the fluid. Rewrite these variables as a dimensionless relationship. Hint: Take 2, p, and D as repeating variables. pAD? Answer: fC (pn³D*)