The post is constructed from concrete and six A-36 steel reinforcing rods. Figure 1 of 1 900 kN 250 mm Part A If it is subjected to an axial force of 900 kN, determine the required diameter of each rod so that one-fifth of the load is carried by the ste and four-fifths by the concrete. Est = 200 GPa, E. = 25 ĠPa. (Figure 1) Express your answer with the appropriate units. d = TF μÀ Submit Value m My Answers Give Up ? Incorrect; Try Again; 2 attempts remaining

The post is constructed from concrete and six A-36 steel reinforcing rods. Figure 1 of 1 900 kN 250 mm Part A If it is subjected to an axial force of 900 kN, determine the required diameter of each rod so that one-fifth of the load is carried by the ste and four-fifths by the concrete. Est = 200 GPa, E. = 25 ĠPa. (Figure 1) Express your answer with the appropriate units. d = TF μÀ Submit Value m My Answers Give Up ? Incorrect; Try Again; 2 attempts remaining

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Similar questions

Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Question j=169" R=2.1" ;f 4- 2.81 d $ 100 08 96 07 h £=0.5" * # >P d=7.3" Material is ASTM A36. Plate is fixed 511 by 4 screws of {"$. using the information provided, calculate the ultimate stress (factored by LRFD) for shear fracture and tensile rupture of block pattern passing through points the shear 3-10-9-4..
A high-strength steel band saw. 29 mm wide, runs over pulleys 1100 mm in diameter. What minimum thickness of the steel band arvey can be used without exceeding a flexural stress of 260? Assume E = 230 GPa. Answer must be in mm. TS aculty « Previous Next Part
Please answer all since they are all connected. UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials A pin-ended timber column of square cross section is to be made. The properties of the column are given: L = 5 m E = 10 GPa Allowable Stress = 10 MPa FS = 2.0 a. Calculate the critical axial load Pcr in the column in kN if the column axial load is 500 kN. b. Calculate the minimum dimension of the square column to safely support an axial load of 500 kN in mm. c. Calculate the critical axial load Pcr in the column in IN IF the column axial load is 800 KN. d. Calculate the minimum dimension of the square column to safely support an axial load of 800 KN in mm.
Please write the complete solutions and Legibly. Rate will be given! Do not just copy asnwers in CHEGG! Thank you :) A singly reinforced rectangular beam section 250 mm wide, 400 mm deep is reinforced with 2-36-mm-dia. rebars, grade G420 enclosed with 10-mm-dia. stirrups. X Calculate the tensile steel stress when concrete crushes at a strain of 0.003. Use f'c = 21 MPa. Use 3 Decimal Places.
Sub: Advance Reinforced Concrete design. Follow the ACI 318 design code for the design. Answer the question with all details. provide the drawings with all details. Don't Copy Paste from Other Solutions please. i will Upvote You Value Óf X1= 27.65 Value Of X2= 395 1- Design the beam BC of the frame shown in Figure 1 for bending moment and shear force according to ACI 318 code requirements. The concrete cover is 30 mm. Dead load and live loads are given in Figure 1. Provide all drawings in detail. Please do check for maximum and minimum flexural requirements, maximum and minimum spacing of the shear reinforcement. f=X1 MPa, fy=X2 MPa D.L.=5 ton/m L.L.= 3 ton/m 6 m 3 m
A bolted connection between a vertical column and adiagonal brace is shown in the figure below. Theconnection consists of three 5/8-in. bolts that join two 1/4-in.end plates welded to the brace and a 5/8-in. gusset platewelded to the column. The compressive load P carried bythe brace equals 8.0k.Determine the following quantities: (a) The averageshear stress τavein the bolts, and (b) the average bearingstress σbbetween the gusset plate and the bolts. (Disregardfriction between the plates.)
need within 1 hour, pls thank u! A single rivet is used to join two plates as shown. If the diameter of the rivet is 3/4 inch and the load P is 7000 lb, what is the average shearing stress developed in the rivet?
hinz 1. For the beam cross section below, determine the amount of steel As required to cause the strain in the tension steel & to be 0.005 just as the maximum strain in the concrete reaches 0.003. fc' = 3000 psi and fy = 60,000 psi. N.A. b= 10"- Cross Section d = 23" [7422 4233 134 S THE THE CALE DES 2 23-c me Like phans 0.005 PANE Strain 0.003 P HOME st 0.85f Stress 6 I.C. Nc NT * * * * * Delorme
Example 3 Estimate the steel reinforcement for the Column as Shown in figures below -010mm@10cm -0.40 m 0mm@20am 10rmma10om Ø 10 / 200 mm c/c 8 Ø 16 mm 410rmm@10cm -90° hook 135 135 hook frommo20cm $10mm@10cm b) 0.40 m 0.10m-
If the force P reached 10 kN, the wooden specimen shown failed in bearing along a surface. Calculate for the average bearing stress along thementioned surface at the time of failure. P' 16 mm Steel 16 mm 90 mm 15 mm Wood P
Seatwork No. 11 whole yellow sheet of paper or bondpaper A rectangular beam having a 7-m simple span is to Support a superimposed dead load of 28 kN/m and a live lood of x. The unit weight of concrete is 24 kN/m² Consider only 1 layer of reinforcements at the tension Zone. Ise Pmax to compute your area of steel. Given fc-40 MPa fg 400 MPa X= ID. No. 1000≤x≤ 2000 424 - 1000 = 1424 N/m 3950 - 2000 = 1,950 N/m