The position of modulation in a transmitter determines whether the circuit is low- level or high-level. The modulation occurs before the output element of the transmitter's final stage with low-level modulation. Because the modulation occurs in the final element of the final stage, when the carrier signal is at its maximum amplitude, high-level modulators require a substantially larger amplitude modulating signal to obtain a reasonable percent modulation. Which of the following is NOT TRUE? Select your answer. When the transmitted power hits 85 percent in high-level modulation, the AM signal becomes distorted. The final modulating signal amplifier in high-level modulation must supply full sideband power, which could be up to 33% of the total transmit power. Low-level modulation has the problem of requiring all subsequent amplifiers to be linear amplifiers, which is inefficient in high-power applications. Low-level modulation has the advantage of using less modulating signal power to attain a high modulation percentage.

The position of modulation in a transmitter determines whether the circuit is low- level or high-level. The modulation occurs before the output element of the transmitter's final stage with low-level modulation. Because the modulation occurs in the final element of the final stage, when the carrier signal is at its maximum amplitude, high-level modulators require a substantially larger amplitude modulating signal to obtain a reasonable percent modulation. Which of the following is NOT TRUE? Select your answer. When the transmitted power hits 85 percent in high-level modulation, the AM signal becomes distorted. The final modulating signal amplifier in high-level modulation must supply full sideband power, which could be up to 33% of the total transmit power. Low-level modulation has the problem of requiring all subsequent amplifiers to be linear amplifiers, which is inefficient in high-power applications. Low-level modulation has the advantage of using less modulating signal power to attain a high modulation percentage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write an 8051 ASM program to load the timer 1 in order to generate 2000 Hz square wave as given in Figure. The square wave should be generated on pin 2 of port 3. Assume the crystal frequency is 16 MHz. ON 4* Delay Delay
What is modulation? Why is it done? Describe one of the types of amplitude modulation
How to calculate the efficiency in frequency modulation and what is the highest value for efficiency in frequency modulation
During amplitude modulation, if the maximum and the minimum values of the envelope are 5V and 1 V respectively, then what will be the value of the modulation index? Will this value of modulation index give rise to over modulation?
An analog signal is to be coded by an ADC. The signal contains significant frequencies up to 6MHz. The quantization error in any one sample value must be within ± 0.5% of the peak-to-peak amplitude range of the ADC. How many binary digits must each sample contain? Apply (or equate) the formulas:Δ = Xmax - Xmin / L - 1where Xmax - Xmin = peak-to-peak amplitude range (XRange)eq[n] = Δ/2 (maximum quantization noise)eq[n] = 0.005 XRange
Please assume modulation.
(i)Electrical pulses can be varied to represent characteristics of an analog voice signal.Propose ONE (1) pulse modulation scheme to represent the voice digitalization signal.Defend why your proposal is the best and support your answer by illustrating theelectrical pulses waveform to represent an analog voice signal. (ii)Phase Shift Keying (PSK) demonstrates better performance than Frequency ShiftKeying (FSK). State your argument and draw a comparison waveform to illustrate theexamples of both shift keying method.
An available channel for FM transmission is 30 kHz wide. The maximum allowable modulating signal fre- quency is 3.5 kHz. What deviation ratio should be used?
Depanment of Electronics Engineering IX. A carrier signal is amplitude modulated by a sinewave. The resulting AM waveform Is shown below. zed 6V 2.5V a) What is the percentage of modulation? b) What is the amplitude of the carrier signal? c) To achieve 75 percent modulation, what amplitude of the modulating signal is needed? d) Calculate the effective voltage of the AM signal SSA AILE Q + Page 4 I 5 X. The frequency spectrum of an AM signal is shown betow: (9 pts)
Determine four distinct types of modulation processes.
Explain what is modulation?
The maximum deviation allowed in a frequency modulation system is 100 kHz; the modulating signal frequency is 10 kHz. The bandwidth requirement as per Carson's rule will be?