The moment of inertia of a helicopter's rotor is 320kg.m². The rotor starts from rest and at t = 0, the pilot begins by advancing the throttle so that the torque exerted on the rotor by the engine (in N.m) is modelled by as a function of time (in seconds) by T = 250t. a) How long does it take the rotor to turn ten revolutions? b) What is the rotor's angular velocity (in RPM) when it has turned ten revolutions?

The moment of inertia of a helicopter's rotor is 320kg.m². The rotor starts from rest and at t = 0, the pilot begins by advancing the throttle so that the torque exerted on the rotor by the engine (in N.m) is modelled by as a function of time (in seconds) by T = 250t. a) How long does it take the rotor to turn ten revolutions? b) What is the rotor's angular velocity (in RPM) when it has turned ten revolutions?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.18P: The drag on an airplane wing in flight is known to be a function of the density of air (), the...

See similar textbooks

Similar questions

The small particle of mass (800 gm) spinning with angular velocity (w₁ = 2.3 rad/s, at r₁ = 400 mm), if we use force (F) to change the Angular velocity to (w₂, and r₂ = 250 mm) the value of F is: W1 Select one: A. None B. F = 5.63 N C. F = 9.47 N D. F = 3.52 N F
YouTube Mall Over... Leeds International... M1 Questions by To... Question Completion Status: QUESTION 2 A car of mass 750 kg moves along a stretch of road which can be modelled as a line of greatest slope of a plane inclined to the horizontal at 30°. As the car moves up the roa for 500 m its speed reduces from 20 ms-¹ to 15 ms-¹. Calculate: a the loss of kinetic energy of the car 65,625) 66,625 67,625) O 68,625)
Using Newton's second law, the movement of a body in a viscous fluid can be modeled. For this case it will be a one-dimensional movement. ec.1) F -FR = ma F: Force applied to the body. FR: Resistance that opposes the fluid to the movement. m: body mass a: body acceleration For a sphere with initial radius R0 = 1 meter and density 8960 kg/m^3 to which a constant force of 3 Kilo Newtons is applied, it is requested: Using Euler's method, find the velocity as a function of time for the first 5 seconds of movement, considering that v(0) = 10 m/s. Use a 1 second step. For this case use: ec.2) FR = 210Rv R: Radius of the sphere. v: velocity Where, in addition, the sphere disintegrates as time passes in this fluid, so its radius is given by the following function: ec.3) R = R0*e^(-t/250)
Given: The plane accelerates in its current trajectory with a= 100 m/s^2 Farag Angle theta= 5° W=105 kips F_drag= 80 kips m= 1000 lbs Find: F_thrust, F_lift Please include the KD. Fthrust Futel t Fueight 000 BY NC SA 2013 Michael Swanbom
Problem Solving: )An object falls from rest in a medium offering a resistonce. The velocity of the object hefore the ohject reaches the ground is given by the differential egua- tion dv/t + V% = 32, t/sec. uhat is the veloaty of the okject one second after it falls ?
is a mass hanging by a spring under the influence of gravity. The force due to gravity, Fg, is acting in the negative-y direction. The dynamic variable is y. On the left, the system is shown without spring deflection. On the right, at the beginning of an experiment, the mass is pushed upward (positive-y direction) by an amount y₁. The gravitational constant g, is 9.81 m/s². DO C.D Frontly у Your tasks: No Deflection m k Fg = mg Initial Condition y m k Write down an expression for the total energy If as the sum Write down an expression for the total energy H Fg = mg Figure 3: System schematic for Problem 4. Yi & X Write down, in terms of the variables given, the total potential energy stored in the system when it is held in the initial condition, relative to the system with no deflection. as the sum of potential and kinetic energy in terms of y, y, yi C After the system is released, it will start to move. Write down an expression for the kinetic energy of the system, T, in terms of…
FLUID STATICS. Only round off in the final answer. Use 3 decimal places. Thank you!Allison places her coffee mug on a spinner and rotates it around its axis. At rest, the mug is 10 cm deep and 6 cm in diameter, and it holds coffee 7 cm deep. What is the maximum angular rotation she can do in rad/s without spilling her coffee?
The left side of this equation tells how much energy Q the cylinder gives to the water while it cools. The right side of this equation tells how much energy Q the water and aluminum cup absorb from the cylinder to warm up. Because it is the same energy, they are equal. What is known in this equation? Mcyl 411.7 g, malum 46.5 g, malum+water = 175 g Can you find: mwater =? g Twater = Talum = 20°C (water and cup of room temperature) 90°C, T; = 35°C (hot cylinder and cool "cylinder+cup+water" temperatures) Tcyl kCal Calum = 0.22, Cwater 1 (specific heat of water and aluminum, measured in units kg-°C What are we looking for is Ccul - How we find it? Plug all the numbers into the equation (1), Ccul will be one unknown which you can calculate from the equation. Important, convert all the masses from grams to kilograms! After you find Ccyl, compare it to known value for the copper 0.093(our cylinder is made out of copper). |Ceyl -0.093| % : · 100% 0.093
A closed thermodynamic system consists of a fixed amount of substance (i.e. mass) in which no substance can flow across the boundary, but energy can. For a closed themodynamic system we cannot add energy to the system, via substance (E ) (1.e. matter which contains energy is not allowed across the boundary) Across the Boundaries E° = No Q = = Yes W mass NO CLOSED = Yes SY STEM m = constant | energy YES Figure 1.1. If the substance inside the thermodynamic system shown in figure 1.1. (i.e. piston cylinder device) is air, is the system a Fixed closed system Moveable closed system A. В.
Q6 The relationship between the velocity, u, of a construction vehicle (in km/h) and the distance, d (in metre), required to bring it to a complete stop is known to be of the form d = au² + bu + c, where a, b, and c are constants. Use the following data to determine the values of a, b, and c when: a) u 20 and d = 40 b) u = 55, and d = 206.25 c) u = 65 and d = 276.25 [Note: Use an appropriate standard engineering software such as MATLAB, CAS calculator, programmable calculator, Excel software]
Energy of a Roller Coaster Car 500 450 400 350 --- 3 300 250 E 200 150 100 50 6 8 10 Time (s) Mechanical Energy ....... Potential Energy -- Kinetic Energy This graph shows different types of energy for a roller coaster car that starts at the top of a large hill and goes down to its lowest point at 6 s. According to the graph, what is the most likely relationship between height and potential energy? Your answer: They are directly related. They are inversely related. There is no relationship between the two. There is not enough information for a conclusion.
Q) A body with a mass of 15 kilograms is moving with a velocity of 3 meters/secand. If a force of 15 N is applied to the body, what its velocity aller 5 socunds? discuss your results please.