The Link AB must be made of steel with a maximum normal stress of 450 Mpa. Any stress above that will break the link. What should the cross sectional area of the link be? If we want to make it 2.5 stronger what should the cross sectional area be? The distributed load is 8kN/m and the concentrated load at C is 20 kN. 8 kN/m 12 C Y20KN 0.4 m 0.4 m D 0.4 m

The Link AB must be made of steel with a maximum normal stress of 450 Mpa. Any stress above that will break the link. What should the cross sectional area of the link be? If we want to make it 2.5 stronger what should the cross sectional area be? The distributed load is 8kN/m and the concentrated load at C is 20 kN. 8 kN/m 12 C Y20KN 0.4 m 0.4 m D 0.4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B 400 mm 20 mm 500 mm 40 mm 7 kN/m 3 m AM 20 kNm 2.5 m 2.5 m 2 m 15 KN A T-beam with the cross-section shown above is subject to the loads shown. a) Determine the second moment of area of the cross-section b) Draw the SFD and BMD c) State the maximum normal stress at locations A, B, and C on the cross-section due to bending
3 The rigid bar EFG is supported by the truss system shown. Determine the cross- sectional area of member AE for which the normal stress in the member is 105 MPa. 0.90 SONRAWING D B R 15 kN -1.2 m 1.2 m-1.2 m-
11. Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate strength in tension. What should be its width w if the structure shown being designed to support a 20-kN load P with a factor of safety of 3? 600 mm- A B 90 480 mm
The pin-connected structure occupies the position under no load. When the loads G A (unknown) and H (16 kips) are applied, the rigid bar EF becomes horizontal. Bar AB 0.75in? 2.25in? is made of aluminum alloy (E=10,600 ksi) and bar CD is made of red brass (E=15, 000 ksi). Determine the weight E and the axial stresses in the B D F 10,000 120 G 4" 4" 2" two bars. 16"
Link AB is to be made of a steel for 15 kN/m which the ultimate normal stress is 400 MPa. Determine the cross- 30° OE sectional area of AB for which the B factor of safety will be 3.0. 20 kN 0.4 m 0.4 m 0.4 m
Q4: determine the maximum tensile and compressive stresses acting normal to the beam. 50 mm 10 kN 100 mm 30 kN 6 m 2m B (2
the bars and truss have a cross section of 250mm^2. If thr maximum average axial stress in any bar is not to exceed 250N/mm^2, determine the magnitude of P of the loads that can be applied 2P 3m 3m -O E 2m B
A truss tie consisting of 2 ISA 75 × 75 x 8 mm carries a pull of 150 kN. At ends the two angles are connected, one each on either side of a 10 mm thick gusset plate, by 18 mm diameter rivets arranged in one row. The allowable stresses in rivet are f 90.0 N/mm2 and f = 250 N/mm2. Maximum tensile stress in the tie in N/mm2 is
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
Link AC has a uniform rectangular cross section 1/8 in. thick and1 in. wide. Determine the normal stress in the central portion of the link.
A truss system is supported by two pins at the top. Determine the absolute value of the axial stress in member AC (in MPa) if the diameter of the member is 30 mm. Sm 36 AN 4m 2m Go kN
8-46. The wide-flange beam is subjected to the loading shown. Determine the stress components at points A and B and show the results on a volume element at each of these points. 500 lb ↓ 2 ft 2 ft 2500 lb B 2 ft 4 ft 3000 lb 0.5 in.- Prob. 8-46 B 6 ft- 0.5 in. 1-4 in T 4 in. 12 in. 0.5 in.