The L-frame in figure below supports forces from two cables. Cable “EAD”passes through a frictionless ring at point “A”, and cable “OCG” passes through africtionless ring at point “C”. The force in cable “EAD” is 800 lb and the force incable “OCG” is 400 lb. For the cable forces applied at points “A” and “C”, using thevector approach determine:a) the moment about point “B”,b) the moment about point “A”, andc) the moment about point “O”. Q.3) The L-frame in figure below supports forces from two cables. Cable "EAD"passes through a frictionless ring at point "A", and cable "OCG" passes through africtionless ring at point "C". The force in cable "EAD" is 800 lb and the force incable "OCG" is 400 lb. For the cable forces applied at points "A" and "C", using thevector approach determine:a) the moment about point "B",b) the moment about point "A", andc) the moment about point "O".Z6 ftB4 ft4 ft|0A5 ftCD5 ftE8 ftyGx

Answered: Image /qna-images/answer/b55c6dd5-bdbd-4648-9190-c5761e396651.jpg

The L-frame in figure below supports forces from two cables. Cable “EAD” passes through a frictionless ring at point “A”, and cable “OCG” passes through a frictionless ring at point “C”. The force in cable “EAD” is 800 lb and the force in cable “OCG” is 400 lb. For the cable forces applied at points “A” and “C”, using the vector approach determine: a) the moment about point “B”, b) the moment about point “A”, and c) the moment about point “O”.

The L-frame in figure below supports forces from two cables. Cable “EAD” passes through a frictionless ring at point “A”, and cable “OCG” passes through a frictionless ring at point “C”. The force in cable “EAD” is 800 lb and the force in cable “OCG” is 400 lb. For the cable forces applied at points “A” and “C”, using the vector approach determine: a) the moment about point “B”, b) the moment about point “A”, and c) the moment about point “O”.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

Find the internal force systems acting on sections 1 and 2.
Find the internal force system acting on section 3 for the pin-connected frame.
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
Q6/A: The crate in figure (7) has a weight of 550N. Determine the force in each supporting cable.
Problem #3: From the given set of non-concurrent forces shown in the figure, determine the Resultant force which could represent them. Figure: Q=20KN IC. T=40KN P=25KN: Im CB W=50KN
2- Find the applied force by the hydraulic cylinder in the truck shown graphically using KS: 1cm=1m, KF: 1cm=1 kN. W=25 kN
A 200-lb weight is suspended from a wall by means of a bracket, where the triangle BOD is in a horizontal plane, as shown in the figure below. Find the forces in OA, OB, and OD.
A uniform trapdoor shown below is 1.0 m by 1.5 m and weighs 300 N. It is supported by a single hinge (H), and by a light rope tied between the middle of the door and the floor. The door is held at the position shown, where its slab makes a 30° angle with the horizontal floor and the rope makes a 20° angle with the floor. Find the tension in the rope and the force at the hinge.
Determine the force Vectors F = 90 N and F43 in the four bar mechanism shown in figure below. Draw the force diagram for the link QB. OQ is 80 Cm. OA is 50 Cm. AB is 70 Cm. QB is 60 Cm. QE is 34 Cm. Link QB at 77 degrees with horizontal. Link AB is 13 degrees with horizontal. Force F is at 32 degrees with horizontal. Link OA is at 60 degrees with horizontal.
In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D connected to F. Determine the following give that Force F is equal to 690.86 N. Note: Express your answer in terms of the units. Observe 3 decimal places. 1.) Determine x-component of vector DF. 2.) Determine the y-component of Vector DF 3.) Determine the z-component of Vector DF. 4.) Determine the moment experienced by the system assuming that there is no wire support.
1000 lb 4 ft 4 ft B 5 ft A 3 ftr 10 ft 13 ft 600 lb -9 ft- 5 ft E Show Transcribed Text The frame is shown in Figure, (a) is supported by a pin at A and rollers at E. Draw the FBD diagram. Find the components of all forces acting on each member of the frame.
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.