The Healthy Chocolate Company makes a variety of chocolate candles, including a 12-ounce chocolate bar (340 grams) and a box ofsix 1-ounce chocolate bars (170 grams).a.Specifications for the 12-ounce bar are 322 grams to 358 grams. What is the largest standard deviation (In grams) that the machinethat fills the bar molds can have and still be considered capable if the average fill is 340 grams? (Round your intermediatecalculations to 2 decimal places and final answer to 3 decimal places.)Standard deviationb.The machine that filles the bar molds for the 6-ounce bars has a standard deviation of .84 grams. The filling machine is set to deliveran average of 1.04 ounces per bar. Specifications for the six-bar box are 150 to 190 grams per box. Is the process capable? Hint: Thevariance for the box is equal to six times the bar variance. Convert all calculations Into grams.O YesO Nogramsc.What is the lowest setting in ounces for the filling machine that will provide capability in terms of the six-bar box? Hint: Use grams tosolve, then convert to ounces. (Round your Intermediate calculations to 2 decimal places and final answer to 3 decimal places.)Lowest settingounces

Given data is LSL = 322 grams USL = 358 grams

Answered: The Healthy Chocolate Company makes a…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

Autopitch devices are made for both major- andminor-league teams to help them improve their batting averages.When set at the standard position, Autopitch can throw hardballstoward a batter at an average speed of 60 mph. To monitorthese devices and to maintain the highest quality, Autopitchexecutive Neil Geismar takes samples of 10 devices at a time. Theaverage range is 3 mph. Using this information, construct controllimits for:a) :X chart.b) R chart.
Webster Chemical Company produces mastics and caulking for the construction industry. The product is blended in large mixers and then pumped into tubes and capped. Management is concerned about whether the filling process for tubes of caulking is in statistical control. The process should be centered on 8 ounces per tube. Several samples of eight tubes were taken, each tube was weighed, and the weights in Table were obtained. Ounces of Caulking Per Tube Tube Number Sample 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7.98 8.33 7.89 8.24 7.87 8.13 8.34 8.22 7.77 8.18 8.13 8.14 8.02 8.08 7.91 7.83 7.92 8.11 7.94 8.51 8.04 8.05 7.99 8.13 8.44 8.41 8.00 7.90 8.10 8.14 7.68 8.28 7.89 8.16 7.81 8.12 7.81 8.09 7.93 7.97 8.14 8.13 8.11 8.16 8.09 8.07 7.88 8.14 a. Assume that only six samples are sufficient and develop the control charts for the mean and the range.b. Plot the observations on the control chart and comment on your findings.
BlueMoon Bottlers has a bottle-filling process with a mean value of 64 ounces and a standard deviation of 8 ounces. Suppose the upper and lower specification limits are 71 and 57 ounces, respectively. What is the process capability index of this process? (Note: You MUST show every single step and detailed derivation for full credit)
Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: a) What is the value of x? x= 156.76 mm (round your response to two decimal places). b) What is the value of R? Day 1 2 3 4 5 Mean x (mm) 158.9 155.2 155.6 157.5 156.6 R = 4.40 mm (round your response to two decimal places). c) What are the UCL and LCL using 3-sigma? Upper Control Limit (UCL) = mm (round your response to two decimal places). Range R (mm) 4.2 4.4 4.3 4.8 4.3 Ç
A process at Printwright, Inc.’s largest facility is used to make plastic gears for a computer printer. The data found in the worksheet Prob. 9-15 were gathered by a quality analyst. The gears were designed to be 3.57 ` 0.05 centimeters (cm) in diameter. Construct a histogram of the data. What can you observe about the shape of the dis- tribution? What would you recommend to the production manager based on your analysis?
A weighing process has an upper specification of 1.751 grams and a lower specification of 1.632 grams. A sample of parts had a mean of 1.7 grams with a standard deviaiton of 0.023 grams. Round your answer to four decimal places. What is the process capability index for this system?
Auto pistons at Wemming Chung's plant in Shanghai are produced in a forging process, and the diameter is a critical factor that must be controlled. From sample sizes of 10 pistons produced each day, the mean and the range of this diameter have been as follows: a) What is the value of X? x= mm (round your response to two decimal places). Day 1 2 3 4 5 Mean x (mm) 158.9 155.2 155.6 157.5 156.6 Range R (mm) 4.2 4.4 4.3 4.8 4.3
Is a capable process a perfect process? That is, does acapable process generate only output that meets specifications? Explain.
Ettlie Engineering has a new catalyst injection system for your countertop production line. Your process engineering departmenthas conducted experiments and determined that the mean is 8.01 grams with a standard deviation of .03. Your specificationsare: m = 8.0 and s = .04, which means an upper specification limit of 8.12 [ = 8.0 + 3(.04)] and a lower specification limit of7.88 [= 8.0 - 3(.04)].What is the Cpk performance of the injection system?
A fast food franchise tracked the number of errors that occurred in customers orders. These included; * wrong menu items *wrong size drink *lack of condiments *wrong price total *and so on... Some orders may have more than one error. In one week, 1500 orders were filled, and a total of 72 errors were discovered. Find the control limits for a C – Chart to monitor the number of errors per order. Is order accuracy, good or bad ? Explain.
Sam’s Long Life 60-watt light bulbs are designed to have a life of 1,350 hours with tolerance of ± 340 hours. A recent representative sample from the process that makes these light bulbs revealed a mean of 1,290 hours, with a standard deviation of 94 hours. Compute a. Compute the process capability ratio and the process capability index, and comment on the overall capability of the process b. Explain to what extent the process for producing Sam’s Long Life 60-watt light bulbs would have to be improved to achieve 4-sigma quality. c. show detail work
Please do not give solution in image format thanku A normally distributed process uses 66.7% of the specification band. It is centered at the nominal dimension, located halfway between the upper and lower specification limits. a) Estimate ?? and ???. Interpret these ratios. b) What fallout level (fraction defective) is produced?

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS