The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the drum is , = 0.15, and the weight of the handle may be neglected. If a counterclockwise torque of 5 ft - Ib is applied to the drum Repeat the problem for a clockwise torque of 5 ft · Ib. What happens to the system at a 4.6 in.? What does the solution mean for a> 4.6 in.? M= 5 lb-ft -12 in. 12 in

The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the drum is , = 0.15, and the weight of the handle may be neglected. If a counterclockwise torque of 5 ft - Ib is applied to the drum Repeat the problem for a clockwise torque of 5 ft · Ib. What happens to the system at a 4.6 in.? What does the solution mean for a> 4.6 in.? M= 5 lb-ft -12 in. 12 in

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.36P: The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find...

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 36° V-pulley is 0.15, and the weight of the han- dle is 15 N. If a force of 200 N is aPplied to the end of the handle, determine the maximum torque for which no mo- tion occurs if the torque is applied Counterclockwise. 150 mm T 200 N 60 150 mmi 675 mm 75 mm
The band brake of Fig. is used to control the rotation of a drum. The coefficient of friction between the belt and the 36° V-pulley is 0.15, and the weight of the han- dle is 15 N. If a force of 200 N is applied to the end of the handle, determine the maximum torque for which no mo- tion occurs if the torque is applied Clockwise. 150 mm T 200 N 60 150 mm -675 mm 75 mm
The band of a brake has a contact angle of 18° deg. If the pulls on the bands are 275 kg and 100 kg, find the coefficient of friction.
The band wrench of Fig. an oil filter from a car. (The filter acts as if it were a wheel with a resisting torque of 40 lb ft.) Determine the mini- mum coefficient of friction between the band and the filter that will prevent slippage. The weight of the handle can be neglected. is used to unscrew 40 Ib-ft 2.5 in. -2 in. 7.5 in.
A flat belt passes over two idler pulleys and under a rotating drumof diameter 8 in. The axle of the drum is free to move vertically ina slot, and a spring keeps the drum in contact with the belt. Whatis the minimum force which should be exerted by the spring if slippageis not to occur when a 30-lb · ft torque is applied to the drum? Thecoefficient of static friction between belt and drum is 0.30 and theangle of contact is 180 degrees.
Please, reaply as soon as posible! Static Problem The band brake shown controls the rotation of the drum. The coefficient of friction between the belt and the drum is 0.25. The weight of the lever is negligible.Determine the force P that must be applied at the end of the braking lever to resist a torque T = 200 lb in, if the torque is applied in the: a) Clockwise b) Counterclockwise direction.
Q5: The block brake, as shown, provides a braking torque of 360 N.m The diameter of the brake drum is 300 mm. The coefficient of friction is 0.3. Find 1. the force (P) to be applied at the end of the lever for the clockwise and counter clockwise rotation of the brake drum, and 2. The location of the pivot or fulcrum to make the brake self-locking for the clockwise rotation of the brake dracs 100 10 ( F₁ 4 μ sin 80 20+ sin20 T = (F₁) r Bearing Area A, b(2r sind) RN = (1 20 R 600 Brake drum
Q2/ Arm ABC acts as a brake on the wheel as shown in Fig. 2. The coefficient of static friction at B is pB = 0.4. Determine the largest moment M that can act on the wheel without causing it to slip? Radius = 200 mm 100 N M 300 шn O B Figure 2 400 mm A 200 mm
Draw the FBD of the problem The coefficient of friction between the inner pulley and the belt is 1/?. Find the maximum value of W that can be supported without rotating the compound pulley P or slipping the belt on the compound pulley P. Pulley B is frictionless. A C "P 200 lb A B W