The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear 1 and rotates at 1200 r.p.m. The gear wheels 2, 3, 4 and 5 are fixed to parallel shafts rotating together. The final gear 6 is fixed on the output shaft. F. Find: 1-the rotating speed of gear 6 2-rotating speed of gears (2, 3, 4, 5) The number of teeth on each gear are as given below:

The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear 1 and rotates at 1200 r.p.m. The gear wheels 2, 3, 4 and 5 are fixed to parallel shafts rotating together. The final gear 6 is fixed on the output shaft. F. Find: 1-the rotating speed of gear 6 2-rotating speed of gears (2, 3, 4, 5) The number of teeth on each gear are as given below:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The gearing of a machine tool is shown. The motor shaft A is connected to gear 1 and rotates at 1000 rpm. Gears 2, 3, 4, and 5 are fixed to parallel shafts rotating together. Thefinal gear 6 is fixed on the output shaft. Determine the following considering the number of teeth on each gear below:a. Speed of gear 2, 3, 4, 5, and 6b. Speed ratio of the gear trainc. Train value of the gear trainGEAR 1 2 3 4 5 6NO. OF TEETH 24 53 27 68 28 64
Two gears mounted on shafts have 10 and 15 teeth, respectively. The center distance is 10 inches. The addendum equals the module, and the clearance equals 0.135 times the module. Determine (a) pitch diameters, (b) addendum, (c) dedendum, and (d) root circles. Draw simple circles showing the diameters and the center distance. Complete solution and drawing is required.
The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion (driver Gear) that rotates at 625 rpm, and idler Gear B and a driven gear (Gear C). The gears have a module of 5mm and a pressure angle of 200. Find the pitch diameter of gear C in mm.
The spur gear arrangement shown in Figure has a pinion (driver Gear A) that rotates at 700 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degree. Given the number of teeth as shown, determine: The pitch diameters of the idler gear. 50 teeth A -90⁰- B 80 teeth C 60 teeth
The spur gearing arrangement made of two parallel shafts,whose pitch circle diameters of driven and driver gears are 86cm and 35cm respectively. If driven shaft runs with 8 r.p.s,determine the following; 1. Center distance between the two shafts in mm. 2. Speed of driver shaft in rpm 3. Velocity ratio 4. Number of teeth's on driver and driven shaft for the given module 5mm
three spur gear arrangement are shown. it has a pinion gear A-driver that rotates for about 500 rpm. the second gear, gear B- an idler and the third gear, gear C- driven gear. the three gears have a diametral pitch of 5 and power of 10hp. The pressure angle is 20°.Number of teeth are shown in the figure. determine the following: i) The pitch diameters of each of the gears. ii) The torque that each shaft is required to transmit. iii) The forces on each of the gears, shown on a free body diagram. iv) The resultant force on the shaft carrying Gear B.
The spur gear arrangement shown in Figure has a pinion (driver Gear A) that rotates at 700 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degree. Given the number of teeth as shown, determine: The speed of Gear C NOTE: Write your answer in two(2) decimal places Example: 488.62 rpm 50 teeth A -90% B 80 teeth C 60 teeth
Figure shown below illustrates the gears in a speed-change gearbox used in machine tool applications. By sliding the cluster gears on shafts Band C, nine speed changes can be obtained as shown in Table given below. The problem of the machine tool designer is to select tooth numbers for the various gears (2 to 10) so as to produce a reasonable distribution of speeds for the output shaft. The gears 2, 6 and 9 are having 20, 25 and 50 teeth respectively. The input shaft speed is 450 rpm and the output speed can vary from 137 rpm to 580 rpm depending on the sequence of the gears. If the output speed obtained through the gear sequence 2-5-5-8 is 257 rpm and if the minimum and maximum number of teeth in the gear system are 20 and 50 respectively, (i) Suitable tooth numbers for the remaining gears (3,4,5,7,8 & 10)
1. Two gears mounted on shafts have 10 and 15 teeth, respectively. The center distance is 10 in. The addendum equals the module, and the clearance equals 0.15 times the module. Determine (a) pitch diameters, (b) addendum, (c) dedendum, and (d) root circles.
Two parallel shafts, about 550 mm apart are to be connected by spur gears. One shaft is to run at 350 rpm. and the other at 140 rpm. Design the gears, if the circular pitch is to be 20 mm. Indicate the corrected values below. (USE 2 DECIMAL PLACES ON THE SOLUTIONS AND THE FINAL ANSWERS.) Pinion: No. of Teeth = Diameter = Gear: No. of Teeth = Diameter =
73 ll 6 O ... The pitch circle radius multiplied by the cosine of the pressure angle. Q3:- The increase of the contact ratio is desirable in gearing design because of:- * All of these The number of teeth will be increased in the engagement region More strength and more gear life will be achieved Smoother and faster motion None of these Q4:- To get best gearing design, it requires to:- * Increase sliding None of these Decrease sliding
A compound epicyclic gear train. Wheels A, D, and E are free to rotate independently on spindle O, while B and C are compound and rotate together on spindle P, on the end of arm OP. All the teeth on different gears have the same module. A, B, and C have 14 teeth, 32 teeth, and 16 teeth respectively, which are cut externally. a) Find the number of teeth on wheels D and E which are cut internally. b) Determine the magnitude and direction of the angular velocities of arm OP and gear E If wheel A is driven counterclockwise at 2 r.p.m while D is driven clockwise at 6 r.p.m., and the number of teeth of gears E and D, are 78 and 62 respectively. (Must use Tabular method) another method not accepted). Steps nber of teeth Step1 Step2 Arm OP Gear A Gear B Gear C Gear D Gear E A