Calculate force in member 25.Note: Remember Given end of the question 25 is not grade. You have to calculate force in member 25 The frame below is subject to applied loads of X = 2 kN and Y = 4 kN. Assuming the frame dimensions A = 1.6, B = 2.6 and C = 2.5,calculate the force in member 25....в (m)3.45A (m)C (m)X (kN).Y (kN).

Consider the FBd of the joint 5 as shown:

Answered: The frame below is subject to applied…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(2.) The following beam is subjected to bending. Consider cross-section K! a + + 쇼 K F + 1/2 + 1/2 + y- + A O e B + a + F = 15 kN 1 = 2.4 m a = 80 mm v = 5 mm a) Calculate the normal stresses at the marked vertices (A and B) of cross-section K, if the following geometric data of the section are given: principal moments of inertia and position of the centroid of the shape. e = 2.230 cm; I₁ = 77.650 cm¹; 1₂ = 18.178 cm*
80 kN 60 KNAD 5 m EA = constant 5 m A ts E5 m 5 m Analyze the truss shown. An additional load of 20 kN downward is loaded at C. Determine the force in member BD. If the force is in compression, input your answer as negative.
8 k Problem # 2 4 ft C Use the Virtual Work as 1 in.? the displacement method. E = 29000 ksi 2 in.? 1 in.2 1 in.? 3 ft 2 in.? Determine the force in each member of the truss. The cross- sectional area of each member is indicated in the figure. Assume the members are pin-connected at their ends. A
A frame and a loading are shown. Note that a = 90° -300 mm- B 200 mm D 175 mm A 400 mm 200 mm Determine the internal forces at point Jwhen P = 1.7 kN. The axial force is 5.143 kN The shear force is 1.5 O kN The bending moment is 1.4786 kN-m
Problem 1 An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A, as shown in figure. The strength properties of the wire and the shear pin at B are o, = 350 MPa (wire), and t,=300 MPa (pin at B). If the wire and pin are to be sized to provide a factor of safety of the wire F.S = 3.3 and a factor of safety of the pin F.S = 3.5. What are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)? dw D 90 mm B 20° 100 mm View a-a of B P = 2 kN
A distributed loading of p = (800x ) Pa acts over the top surface of the beam shown . Determine the magnitude and location of the equivalent resultant force.
Problem (5) The simply supported beam AB is used to support the following loadings as shown. Weight for the beam is neglected. Determine the internal forces at: • Point C located at distance 2m from A. Point D. 10KN 2 AN/m 5 m 3m -2m-
Solve the problem with complete and neat solution. Draw the figure. Determine the force in each member of the bridge truss shown. State whether each member is in tension or compression. 100KN K 3m 3m B
Problem 1 An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A, as shown in figure. The strength properties of the wire and the shear pin at B are , = 350 MPa (wire), and t-300 MPa (pin at B). If the wire and pin are to be sized to provide a factor of safety of the wire F.S = 3.3 and a factor of safety of the pin F.S = 3.5. What are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)? D 90 mm 20° 100 mm View a-a of B P = 2 kN
Determine the maximum bending moment for the beam shown below. Use a = 9 ft, b = 13 ft, c = 7 ft, and w = 15 kips/ft. The reaction forces for this beam are Ay = 90.8 kips and Dy 104.2 kips. %3D %3D В C D a b Answer: Mmax i kip-ft
The truss shown below is pined at A and has a roller at F. The Load applied at E is P=20 KN. The member GF is to be replaced. Determine the magnitude of the force F, in kN, that is required at C in order to safely disconnect GF. Give your answer to one decimal place. 3.5m 3.5 m -B 3.5m F KN 459 3.5m 45° D 3.5m 45° PKN
PROBLEM 1 The frame is used to support a wood deck that is to be subjected to a uniform load of 6.0 E KN/m?. Sketch the loading that acts along members BG and ABCD. Let b=5m G and a=2.5m H

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The frame below is subject to applied loads of X = 2 kN and Y = 4 kN. Assuming the frame dimensions A = 1.6, B = 2.6 and C = 2.5, calculate the force in member 25.