the force needed to deflect 1 inch of length is called

Q: Which of the following is not considered as a lower pair

A: 1. Option (c)  Roller pair  is correct option. Explanation: As we know that line and point contact…

Q: 4. Describe the difference between low pairs and high pairs

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: To move something that weighs more than you do, using a lever, move the item closer to the___. A.…

A: c) fulcrum

Q: What will be the value of F,? 10 kN 5 kN + F1 F2

A: Resolve the other 3 components in terms of force F1. The 10 kN along the F1 is = (10 x cos90) = 0…

Q: What is the total degree of freedom (DOF) of

A: To find Total DOF

Q: Mechanical advantage is the ratio of effort to load. a) True b) False

A: Mechanical advantage is the ratio of effort to load. a) True b) False

Q: higher or lower than that on the Earth lower than that on the Earth same as that on the Earth higher…

A: Given:

Q: What do you mean by Redesign the structure so it is more tolerant of statements

A: Given  Redesign the structure so it is more tolerant of statements To find Meaning of the statement…

Q: A B - 3 ft - 6 ft - 3 ft 2 in. 6 in. 2 in. I in. in.

A:

Q: Breaking an Xline: a. Creates a line and a ray b. Creates two rays c. Converts the Xline to polyline…

A: In AutoCAD software, XLINE is a command which is used to draw a line of infinite length. Generally,…

Q: Which of the following is not the drilling hazard? a. Pipe stuck b. Tools dropped while drilling…

A: From the following the option which is not drilling hazard is

Q: The loads which tend to increase the length the body is called

A: There are many types of load by which the length of a body changes.

Q: Question 8  I put C and it was incorrect

A: To determine: Correct technician among A and B who are discussing the suspension and ignition switch…

Q: In figure 2 a) what is the total weight of all bodies?

A: Solution:

Q: FOR fixed support , the number of unknowns are ?

A: FOR fixed support, the number of unknowns are? 2 3 1 4

Q: le load it can take is (B) 33.48 KN

A:

Q: hing 3304 kN is If the block is 9

A: Weight of block = 3304 kN Weight of sea water displaced = volume of water x density Volume of water…

Q: 5 kip/ft 15 kip ft 15 kip ft B 6 ft 10 ft 6 ft

A:

Q: If a force doubled, impulse will triple. True or false

A:

Q: Draw the free body diagram Always use 3 decimal place

A:

Q: 5 kip/ft 15 kip ft 15 kip · ft B- 6 ft 10 ft 6 ft

A: Given figure:

Q: How many cubic feet of metal are required to make 1000 funnels such as the one shown in the sketch…

A: The periphery enclosing a certain amount of volume in space is termed as the curve surface area.…

Q: The amount of deflection of the beam depends upon

A:

Q: F = 250 lb - 30°, 45 F2 = 375 lb

A:

Q: Find Ixx and Iyy of lamina in given figure;

A: Given Section To find Moment of inertia about X axis Moment of inertia about Y axis

Q: to move a force of 1713 lbs using a 100 psi what size bore in diameter would it need in inches

A: Given data: F=1713 lbsσ=100 psi Need to determine the size bore in diameter.

Q: To move something that weighs more than you do, using a lever, move the item closer to the __. A.…

A: A lever is consist of three parts Fulcrum is the fixed point around which the bar pivots Effort arm…

Q: A shift lever ball has diameter 2.535 in. What is its volume in cubic inches

A: Given   Diameter, d = 2.535 in       Radius, R = 1.2675 in Find    Volume, V

Q: ke angle is 0°. The minimum value of sh

A:

Q: A lead cube has a mass of 85.3kg. Solve for the length its side in cm. Assume sg to be 11.36

A:

Q: 2 kip/ft 50 kip - ft 50 kip · ft B 10 ft 20 ft 10 ft

A:

Q: C 3 ft B 0.8 ft A

A:

Q: Magnitude of AL = 275 pounds Find: TAG= 0 = 5 0 Pounds A Jø B D = 450 pounds

A:

Q: Removal of ice after it has formed on an aircraft structure is called _____

A: Whenever aircraft fly over very high altitude conditions and in winter-like conditions then there a…

Q: inclined plane, on the plate to mak

A:

Q: Which distance represents height of the fall for measurement of the time?

A: In the question, a machine is given and when it rotates it is needed to find out the height and time…

Q: Derive an expression for the height of Proell governor.

A: The answer is in next step

Q: haft trar Is, then t

A: given:power P=1000kwω=100rad/s

Q: Truck can haul 3,790 pounds of gravel . What is the maximum amount of gravel Jerry can haul in 9…

A: Amount of gravel that a truck can haul w = 3790 lb Total no.of loads…

Q: 12. How much wall thickness is there between the counterbore and the sides of the counterweight?

A: T=0.063 Answer

Q: Compute the degree of freedom.

A: Number of links in the mechanism= 10 Number of joints in the mechanism= 12 Number of higher pairs in…

Q: When measured the moment of force, it need tunneling point *

A: This question is based on the concept of moment of force

Q: If a washer has a 1” outside diameter and a .50” inside diameter, what is the distance between the…

A: Given data, D= 1 in.  d= 0.50 in.

Q: Which side will go down? A! 5m 5m 10KG 5KG B

A:

Q: . The number of degrees of freedom

A: Given; From the given figure;   No. of D.O.F of the planetary gear train ;

Q: A rod consists of two parts that are made

A: Kindly refer attached files.

Q: number of degrees of freedom

A: Number of links =6 Primary/lower pair joints=7 Higher pair joints =0