The following data are taken from a 20mm in diameter bar of length 250mm, the following results were recorded. Assume that the curve of the stress-strain diagram i linear from the origin to the first point. P (load in kN) ô(elongation in mm) 112 0.2 154 0.3 167 0.4 174 0.5 181 0.6 Determine the a. Stress at 167 kN load in MPa b. Strain at 167 kN load in mm/mm (expressed in scientific notation) c. Modulus of elasticity in MPa

The following data are taken from a 20mm in diameter bar of length 250mm, the following results were recorded. Assume that the curve of the stress-strain diagram i linear from the origin to the first point. P (load in kN) ô(elongation in mm) 112 0.2 154 0.3 167 0.4 174 0.5 181 0.6 Determine the a. Stress at 167 kN load in MPa b. Strain at 167 kN load in mm/mm (expressed in scientific notation) c. Modulus of elasticity in MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(Problems No. 1- 3) The state plane stress at a point is represented by the stress element below. Determine the stresses acting on an element oriented 30 degree counterclockwise respect to the original element. Calculate the normal stress at the y-axis 60 MPa 20 MPа 90 MPа O a. 75.60 MPa O b. -24.60 MPa 69.8 MPa O d. -39.8MPA
The state of stress at a point is shown on the element. Enter your answers numerically separated by commas. ΥΠ ΑΣφ vec max min = ksi Submit Request Answer Figure Part B Determine the absolute maximum shear stress. ΑΣφ ve 2.5 ksi ksi Fabs mar= 4 ksi Submit Request Answer 5 ksi Provide Feedback 圓

Figure 40° 3 ksi B Determine the stress components acting on the inclined plane AB in (Figure 1), where Try = 6.9 ksi. Solve the problem using the method of equilibrium. Express your answers, separated by a comma, to three significant figures. Or = Tr'y' = Submit Provide Feedback AΣo↓↑ vec Request Answer ? ksi, ksi Next >
0° The stresses at a point in a bar are o1 = 29 N/mm2 (tensile) and o2= 14 N/mm2 (compressive) as shown in Figure (a) Determine the normal, tangential and resultant stress in magnitude and direction on a plane inclined at 55° to the axis of the major stress. (b) Determine the maximum intensity of shear stress in the material at the point. (c) Also, solve the same problem using Mohr's circle method and compare the results. Axis of Major Stress 55 02
Q.5 A component of machine made of steel which resist a biaxial state of stress o,= -120 MPa and t = 100 MPa. Check whether this part is safe or fail using 1. Max. principal stress theory 2. Max principal strain theory 3. Max. distortion energy theory.
Question The state of 2D-stress at a point is given by the following matrix of stress: [0x %]-[ 100 30 30 20 = MPa 0. What is the magnitude of maximum shear stress(Radius of Mohr's circle) in MPa?
The stresses shown act at a point on the free surface of a stressed body. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 97 MPa, Sy = 37 MPa, and Sy = 71 MPa. Assume ß = 58°.Determine the normal stresses o, and ơ, and the shear stress Tng at this point if they act on the rotated stress element shown. Ssy Tnt ơn Answers: MPa i O, = MPa i MPa Tn =
What is Mohr's circle of stress? At a point in an elastic material, a direct tensile stress of 60 kN/mm² and a direct compressive stress of 40 kN/mm² are applied on planes at right angles to each other. If the maximum principal stresses are limited to 75 N/mm² (tensile). Find the shear stress that may be allowed on the planes. Also determine the minimum principal stress and the maximum shear stress. 10001
PROBLEM 1 A circular aluminum tube of L=600mm is loaded in by compressive forces at its ends. The outside and inside diameters are 75mm and 63mm respectively. A strain gage is placed on the outside of the tube to measure nomal strains in the longitudinal direction. E=73 GPa and Poisson's is 0.33. a. If the normal stress in the tube is 57 MPa, what is the load P? b. if the strain is 781 X 10-6, what is the shortening of the tube? What is the percent change in its cross-sectional area.
20 ksi 40 ksi 60 ksi The differential element above represents the state of plane stress at a point in a steel beam. Which of the following best represents the magnitude of the second principal stress (02) at the point? 76.6 ksi O 63.3 ksi 36.6 ksi 60.0 ksi
A tapered cantilever beam AB having rectangular cross sections is subjected to a concentrated load P = 46 lb and a couple Mo = 790 lb - in. acting at the free end [see the figure part (a)). The width b of the beam is constant and equal to 1.0 in., but the height varies linearly from ha = 2.0 in. at the loaded end to hp = 3.0 in. at the support. Use L = 20 in. Мо В hg (a) 3P qo = T Мо (b) ЗР 90 =7 \ Mo.
QUESTION 3. The state of plane stress at a point on the tail of Turkey National Combat Aircraft is shown in the figure. Applying both analytical method and the Mohr's cicle, determine a. Determine principal stress values b. Calculate the maximum inplane shear stress and average normal stress. c. Draw the element location for each condition. d. Determine the absolute maximum shear stress value at the same point. 40 MPa TAI 200 MPa 80 MPa