Kailasben The device is used to measure a change in temperature. BarsAB and CD are made of A-36 steel and 2014-T6 aluminumalloy respectively. When the temperature is at 70° F, ACE is inthe horizontal position.Figure1.5 in.-0.25 in.B3 in.< 1 of 1JuulumbulPart ADetermine the vertical displacement of the pointer at E when the temperature rises to 160 ° F.(Figure 1)Express your answer with the appropriate units.SE =SubmitOValueProvide FeedbackUnitsSwPrevious Answers Request Answer?X Incorrect; Try Again; 5 attempts remaining

Answered: Image /qna-images/answer/14fceea3-89b8-4e04-8c09-d17f2fd14ed0.jpg

The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and 2014-T6 aluminum alloy respectively. When the temperature is at 70° F, ACE is in the horizontal position. Figure 1.5 in. -0.25 in.-- 3 in. 1 of 1 ululaul Y Part A Determine the vertical displacement of the pointer at E when the temperature rises to 160° F. (Figure 1) Express your answer with the appropriate units. SE = Submit LO HÅ Value Provide Feedback Units Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining

The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and 2014-T6 aluminum alloy respectively. When the temperature is at 70° F, ACE is in the horizontal position. Figure 1.5 in. -0.25 in.-- 3 in. 1 of 1 ululaul Y Part A Determine the vertical displacement of the pointer at E when the temperature rises to 160° F. (Figure 1) Express your answer with the appropriate units. SE = Submit LO HÅ Value Provide Feedback Units Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.13P: Figure (a) shows the cross section of a column that uses a structural shape known as W867...

See similar textbooks

Similar questions

Find the ox value for the plate as shown below, where b1=d2%=D16 mm, d1=70 mm,b2%=90mm. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNITS GIVEN IN THE BRACKET) b1 b2 d2 d1
At a temperature of 38.2 °C a 0.49-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 125.9°C, determine the change in length of the steel rod if L= 336.13 mm and M = 210 mm. Round off the final answer to four decimal places. d ... M - A B Aluminum A = 2000 mm2 E = 75 GPa a = 23 x 10-6/°C Stainless steel A = 800 mm2 E = 190 GPa a = 17.3 x 10-6°C
Solve step by step dont use chatgpt DETERMINE THE DIAGRAM OF THE MECHANICAL ELEMENTS 0 995 2m Z 11 3m W₁ = 1 ton m 21 w₂= 2 tun m 12.5m
A metal has a flexural stress of 564 Pa. The W is measured to be 1 meter, while the load was 10 N. The thickness of the metal is twice its L. Using the formula on the three-point test of materials, compute for the thickness of the metal in centimeters.
Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a constant temperature of 32 °C on both sides using an electric heater generating heat at a rate of Q = 0.5 W which is dissipated to air from both sides of the plate. Consider the temperature of the wind/air as 20 °C and assume that the wind speed does not exceed 100 m/s. The properties of air at this temperature are given as; specific heat capacity Cp = 1.005 kJ/kg-K, thermal conductivity k = 0.0253 W/m-K, Density p = 1.19 kg/m³, and kinematic viscosity v = 1.522 x 10 5 m²/s.
Da =5 cm D;=3 cm 1 mm mm T=220°C
When force P is apliced to the rigid arm BC, point B moves downward 0.2mm. Determine the enlongation developed in wire CD: ___ mm. Calculate your answer to 2 digit place.
asap
The steel plate has the dimensions shown. Determine the maximum axial force P that can be applied so as not to exceed an allowable tensile stress of 21 5. ksi. See the stress concentration factor charts on Blackboard in the tables and charts folder. 0.25 in. S in. 0.25 in. 2.5 in. 0,25 in?
In the Figure 3, if m=15 kg and 0-30°, then the weight component of the block parallel to the inclined surface is (in N): m Figure 3: 0 الاختيارات 75.5 O 77.5 O 73.5 O 71.5 O
A solid prismatic rod is L; = 390 mm long and has a circular cross section with a diameter of d = 40 mm. After the temperature of the unconstrained rod is increased, its final length is measured as L₁ = 390.270 mm. Determine the change in the rod's diameter after the temperature increase. Answer: Ad = i mm
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 80.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.70 MN, pressure vessel bolts aide port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm.