The D flip-flop is created by connecting two gated D latches serially, and inverting the CLK input to one of them. The following figure shows the internal circuit of D Flip-flop composing of two latches (L1: Master, and L2: Slave) and NOT gate. Answers the following questions. (Note: You should show all the steps) When CLK = 0 and D = 1, what are the values of N 1 and Q? N 1 = ? Explain how come. Q= ? Explain how come

The D flip-flop is created by connecting two gated D latches serially, and inverting the CLK input to one of them. The following figure shows the internal circuit of D Flip-flop composing of two latches (L1: Master, and L2: Slave) and NOT gate. Answers the following questions. (Note: You should show all the steps) When CLK = 0 and D = 1, what are the values of N 1 and Q? N 1 = ? Explain how come. Q= ? Explain how come

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 8R: For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature...

See similar textbooks

Similar questions

A coil has a resistance of 18 when it mean temp is from 20o C to 50o C. Find its mean temp rise when its resistance is 21 and the surrounding temp is 15o C. A potential difference of 250 V is applied to a copper field coil at a temp of 15o C and the current is 5A. What will be the mean temp of the coil when the current has fallen to 3.91 A, the applied voltage being the same as before.
Write the solution
google.com/forms/d/e/1FAlpQLScF2Wzu92iVI-tEM2nxdhqXrGdR460G4QCTxaUZZeC678PqTg/formResponse مطلوب /06 *:The potential at point P due to Q1 and Q2 is Q, = 1x10-12C 0.5 m 0.5 m Qz = 1x10-12C %3D 50 cm 0.01797 V Ov O -0.01271 V O 0.01271 V O Insert PIC F10 F11 F12 F6 F7 FB Backspace 9 € P Enter H
We want to investigate how the field strength will be with air as dielectric and with steatite. A plate capacitor is placed in a 24 kV network between phase and ground. The relative permittivity of air is &=1 and for steatite &-6. The plate capacitor has area = 1m². The distance between the electrodes is 2 mm. Ep = 8.854-10-12 F/m A=1m² d=2mm a) Calculate the maximum field strength in the plate capacitor. (Answer: 9.8kV/mm) b) What is the capacitance of the capacitor if we use steatite? (Answer: C = 26.6nF)
write your solution plsssss
Give solution
A generator rated at 30MVA, 11kV has a reactance of 40%. Calculate its p.u. reactances for a base of 50MVA and 10kV. O 0.606 p.u. O 0.506 p.u. O 0.806 p.u. O 0.706 p.u.
A resistor and a capacitor are connected in series across a supply of 250 V. When the supply frequency is 50 Hz the current in the circuit is 5 A. When the supply frequency is 60 Hz, the current is 5.8 A. Find the value of the resistance. Ans: ___ ohms
AC 15. What would the equivalent resistance be of a 159 uF capacitor? 16. What is the RMS voltage of a circuit if the peak voltage is 170 volts? 17. If the RMS voltage is 240 volts AC, what is the peak voltage? 18. What is the formula for finding an inductors equivalent resistance? 19. What is the equivalent resistance of an inductor with 0.17 henrys? 20. What is the symbol of an AC power source? 21. What is the equivalent inductance of a parallel circuit with a 0.01L, 0.02L, and 1.7L inductor? 22. What is the equivalent inductance of a series circuit with a 0.03L, 0.04L, and 1.6L inductor? 23. A transformer with a primary voltage of 480 volts and a turns ratio of 2:1 will have what secondary voltage? 24. A Power Network is comprised of what three components? 25. What is the main difference between a fuse and a circuit breaker?
The network Nc shown below in Figure 1.99(a) contains a combination of scaled capaci- tors in series and parallel connections. Using the vahues as shown, you are asked to do the following. (a) Calculate the value of the terminal capacitance Cab at terminals a-b. (b) To obtain an equivalent capacitance Ceq of 1.5F, Nc is to be placed either in series with a capacitance Cz as shown in Figure 1.99(b) or in parallel with Cx as shown in Figure 1.99(c). Determine which connection is correct and calculate the value of C; that will produce the value of 1.5F for Ceg- 4F 2F 3F 1F C OF (a) N. N. 2. (b) (c) Figure 1.99 (a) Capacitor combo Nc (b) Nc in series with C, (c) Ne in parallel with C,
k) A coil consists of 2000 turns of copper wire having a cross-sectional area of 0.8 mm2. The mean length per tum is 80cm and the resistivity of copper is 0.02u 52-m. Find the resistance of the coil and power absorbed by the coil when connected across 110v d.c. supply.
For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature setting of ___________ F (_____________ C). Some states have laws stating a maximum temperature setting of ____________ F (________________ C).