The couple-moment Mc in the system shown is 7500 kip-in, counterclockwise, 10 kip and the length of segment CD is 100 inches. Determine forces F1 and F2 (both in kips) if the system shown can be replaced by an equivalent force, R equal to 150 kips directed from H to A, and a couple-moment MA. What is MA, in kip- inch? Note that the sense of F1 and F2 are 50 kip E just assumed. 15 kip 35 120 A 60 80" Mc 15° 80" 160 25 kip 80" 50 kip 35 15 kip -120".

The couple-moment Mc in the system shown is 7500 kip-in, counterclockwise, 10 kip and the length of segment CD is 100 inches. Determine forces F1 and F2 (both in kips) if the system shown can be replaced by an equivalent force, R equal to 150 kips directed from H to A, and a couple-moment MA. What is MA, in kip- inch? Note that the sense of F1 and F2 are 50 kip E just assumed. 15 kip 35 120 A 60 80" Mc 15° 80" 160 25 kip 80" 50 kip 35 15 kip -120".

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2/174 Calculate the moment Mo of the 250-N force about 30 the base point O of the robot. 20° 400 mm A 60% 250 N 500 mm B 300 mm
Determine the required magnitude of the couple moments M2 & M3 and so that the resultant couple moment of the system shown in Figure Q6 is 052 N.m? M2 45° M3 M = 300 N-m w] TOSHIBA F5 F6 F7 F8 F9 F10 F11 F12 INS SCROLL L &.
The force-couple system shown acts on atrapezoidal plate. a. Determine thevalue of M, if the system shown is equivalent to a single force acting at point C. b. The system shown is equivalent to a force couple system consisting of R and M2= 3000 kip-in clockwise. If M, in this case is 120 kip-in counterclockwise, determine the point of action of the resultant force R along line CD. 50° 1YZ kips 10 in 1X in 10 in 20 kips 35 kips 8x kips 2Y in 5o 1YZ kips Parameters X = 7, Y = 3, Z = 7 1X in 17 in 23 in 87 kips 137 kips 2Y in 8x kips 1YZ kips 18 in
2) The box beam is constructed from four boards that are fastened together using nails spaced along the beam every 2 inches. The beam is subjected to a maximum internal shear force of 475 lb. a) Locate the neutral axis and compute the moment of inertia for the cross-section in in*. [Ans. to check: 1 = 197.7 in¹] b) Calculate the first moment of area in in³ at each of the two connection interfaces (i.e. once for the top flange and once for the bottom board). Draw a clear sketch of the cross-section showing the neutral axis and the necessary dimensions to calculate the first moment of area. [Ans. to Check: Qtop = 31.2 in³] c) Compute the shear flow occurring between the wood and the nails at each of the two connection interfaces in lb/in. [Ans. to Check: qbottom = 49.0 lb/in] d) Design the section by choosing the required shear strength of the nails (in lb). Check both interfaces but choose only one assuming you would like to use the same nails for the entire beam. [Ans. to check: 75 lb…
Calculate the internal actions (V, F and M) in the section 1 meter to the right of E in ECD element.
ホーaxis GON 554° 300 Find the t-component of the Rsulteant OF the force sysem shown.
Problem 7.5 For the cantilever beam shown, it is required to determine the point where two bars theoretically can be cut off from the standpoint of the calculated moment strength, OM, of the beam. f, = 420 MPa and f.'= 21 MPa. 420 3@80 = 240 90 mm 90 mm 75 mm 10mmø stirups 4-28mm¢ W. 3.6 m 800 mm 725 mm 12. Calculate the moment the moment strength, ØM, , of the section. [in kN-m] 13. Calculate the maximum factored uniform load, w, the beam could support. [in kN/m] 14. Determine the distance from the free end where two bars theoretically can be cut off. [in m] 15. Determine the distance from the free end where two bars actually can be cut off. [in m] 16. Calculate the required development length, f dr at the support, if 90 hooked bars are used. [in mm]
UAB = 1 wac = ? *16-60 The slider block C moves at 8 m/s down the inclined groove. Determine the angular velocities of links AB and BC, at the instant shown. Cotohon around a fixed ³8 = WAR X PAB cand off = _WAB K x (2i) = -2WABj →general plane of motion → √₂ = vc + BCB/C - 2 m -2WABJ = 8 sinus 18 twBck * 25 FB/1C 45 A 45° TAB WAB # B ль BIC 2 m SUBC с 45 Vc = 8 m/s 8 $145 T
otorm Snie F-A0ON P:450 N Find the magnitude 30° 45 and direction of the 30° resultant of the three forces P, F,Q in the figure Q:700 N
The force-couple system shown acts on a trapezoidal plate. a. Determine the value of M, if the system shown is equivalent to a single force acting at point C. b. The system shown is equivalent to a force-couple system consisting of R and M2 = 3000 kip-in clockwise. If M, in this case is 120 kip-in counterclockwise, determine the point of action of the resultant force R along line CD. 50 1YZ kips 10 in 1X in 10 in B 20 kips 35 kips 8X kips 2Y in M1 50 1YZ kips Parameters X = 7, Y = 8, Z = 4 1X in 17 in 2Y in 28 in 8X kips 1YZ kips 87 kips 184 kips 18 in
2/77 The device shown is a part of an automobile seat- back-release mechanism. The part is subjected to the 4-N force exerted at A and a 300-N•mm restor- ing moment exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force. F = 4 N 10 mm 15° A 40 mm 300 N•mm Problem 2/77
Homeworks: A steel shaft of two segments AB and BC which are rigidly fastened at B Determine: 1) Reactions at A and C. 2) Maximum angle of rotation. 1000N. mn/mm 4m 100mm S0mm 5mm