The block has a mass of 4.0 kg and rests on the smooth plane as shown in (Figure 1). Figure k = 200 N/m 0.3 m 0.4 mi < 1 of 1 > Part A Determine the unstretched length of the spring. Express your answer to three significant figures and include the appropriate units. lo = Submit μÀ Value rovide Feedback Request Answer C Units ? Next >

The block has a mass of 4.0 kg and rests on the smooth plane as shown in (Figure 1). Figure k = 200 N/m 0.3 m 0.4 mi < 1 of 1 > Part A Determine the unstretched length of the spring. Express your answer to three significant figures and include the appropriate units. lo = Submit μÀ Value rovide Feedback Request Answer C Units ? Next >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

*** *Show your correct and complete solution neatly. ASAP! Thanks. Given the vibrating system below: K4 Y(t) =Ysin30t where fc: = 30 and K1 Y=20mm Find the following: m C3 C2 C5 C4 M = 10 kg K1=100 N/m K2= 80 N/m K3=75 N/m K4= 120 N/m C1 = 20Ns/m C2= 40 Ns/m C3= 35Ns/m C4-15 Ns/m C5=10 Ns/m 1. Type of Damping 2. Equation of motion x(t). Assume Initial conditions for displacement and velocity. 3. Graph 2 cycles of the vibrating system. You can use third party app for this.
k, k3 A В k2 What is the equivalent spring stiffness between the points A and B. If ki = 1 N/m, k2 =1 N/m. k3 = 2 N/m and k4 = 2 N/m A N/m
Q1: Determine the equivalent spring constant of the system shown in Fig. 1 k₁ k3 0000 mão S k₂ 0000 ks 0000-0000 eeeeeeee K₁ Fig.1
asap
EFx=0= (0.433 F1) - (0.667 F2) - (0.866 F3) + (0.342 P) EFy=0= - (0.250 F1) + (0.667 F2) EFz=0= (0.866 F1) + (0.333 F2) + (0.500 F3) - (0.940 P) Find the magnitude of F1, F2, and F3
A 40lb weight is stretched to the end of a spring. The spring is stretched 6in. Find the displacement from equilibrium of the weight after pi/8 seconds, if the weight is released from rest at 10 inches above the equilibrium. round to the nearest tenth of a foot.
The circuit has been designed to crush a car body into bale using a 150 mm diameter hydraulic cylinder. The hydraulic is to extend 2.50 m during a period of 10s. the time between crushing strokes is 8 min. the following accumulator gas absolute pressures are given: P1 = Gas precharge pressure 90bar(abs), P2 = Gas charge pressure when pump is turned on 200 bar(abs) = pressure relief value setting,P3 = Minimum pressure required to actuate load 125 bar (abs).Calculate: (i) the required size of the accumulator (ii) What are the pump hydraulic kW p
Consider the following spring system. Assume down is the positive direction. Write the stiffness mirix K- • Compute the displacements caused by the external forces f = - Displacement = C₂ m mi heees3 m₂ Hom 3 7/////// with spring constants c = 134
A wagon weighing 5100 Kg moving at a speed of 8 km/h has to be brought to rest. Springs made of wire diameter 25mm with a Dm of 250mm and with 24 turns are available. Find the number of springs required in buffer to stop the wagon at a compression of 180mm. b)A close coiled helical spring is made of diameter wire 25mm. The spring index is 8. Findthe number of turns required and maximum allowable load if the allowable shear stress is100 MPa and elongation is limited to 40mm. [G=80 GPa
Given the vibration system with multiple degree of freedom. For string 1, k1 = 10kN/m %3D For string 2, k2 = 20KN/m For string 3, k3 = 30 kN/m %3D mass = 500kg mass of the beam will not be consider. Solve for the following: i. Frequency j. Period
Q5/ In vehicle suspension design it is desirable to minimize the mass of all components. You have been asked to select a material and dimensions for a light spring to replace the steel leaf-spring of an existing truck suspension. The existing leaf-spring is a beam, shown schematically in the figure. The new spring must have the same length L and stiffness S as the existing one, and must deflect through a maximum safe displacement 8max without failure. The width b and thickness t are free variables. L Load F 6= 1 FL³ 48 EI 10₂L² 6 #E 1=bt³/12 8max = Derive a material index for the selection of a material for this application. Note that this is a problem with two free variables: b and t; and there are two constraints, one on safe deflection 8max and the other on stiffness S. Use the two constraints to fix free variables.
spring is to be inserted with an initial compression to produce a force equal to 125 N between the right-hand end of the lever and the stop. When the maximum force at A reaches to a value of 200 N, the end of the lever moves downward by 25 mm. assuming a spring index 8 determine the following parameters: 1. Spring rate 2. Size of the wire 3. Outside diameter of the spring 4. Number of active coils, and 5. Free length, assuming squared and ground ends Note: the allowable shear stress may be taken as 420 MPa, and G = 80 GPa. Hint: Ans. 0.33 N/mm: 3.4 mm; 27.2 mm; 77 mm - 200 mm - 200 mm Lever Stop -Spring