The beam has the cross-sectional area shown in (Figure 1). Figure 1 of 1 Part A Determine the largest intensity of distributed load w that the beam can support so that the bending stress does not exceed max = 22 ksi Express your answer in kilopounds per foot to three significant figures. w= Submit 9 || ΑΣΦ.11 | vec | Request Answer < Return to Assignment Provide Feedback ? kip/ft

The beam has the cross-sectional area shown in (Figure 1). Figure 1 of 1 Part A Determine the largest intensity of distributed load w that the beam can support so that the bending stress does not exceed max = 22 ksi Express your answer in kilopounds per foot to three significant figures. w= Submit 9 || ΑΣΦ.11 | vec | Request Answer < Return to Assignment Provide Feedback ? kip/ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1. Figure below shows a simply supported beam that has a rectangular cross section 120 mm wide and 200 mm high. a. Determine the maximum bending stress in the beam. b. Calculate the bending stress experienced by a point on section B that is 25 mm below the top of the beam. (Consider the distance of this point from the N.A when solving this part) |15KN 6 kN/m B D 0.8 m 2 m 1.0 m R = 14 kN RE = 19 kN
Determine the internal normal force and shear force, and the bending moment in the beam at points C and D. Assume the support at B is a roller. Point C is located just to the right of the 8-kip load. For your explanation section, complete a FBD of the other side of the beam from the version you did to solve the problem. 8 kip 40 kip · ft A to to D B- 8 ft 8 ft- -8 ft
Q2-The tubular shaft is to have a cross section such that its inner diameter and outer diameter are related by d-0.8 d. Determine these required dimensions if the allowable bending stress is Gallow = 155 MPa., shown in Fig. (2). 15 kN/m mil Figure (2) 3m 60 kN m 1 m-
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 ft, b=8.0 ft, c=4.0 ft, d=3.0 ft, w = 6.5 kips/ft and P = 45 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a B a W B W C b d For this loading, calculate the reaction forces Ay and Ey acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) b C C P C D P Ľ E d E ·x Ey
Question 3 Determine the maximum bending stress in the steel beam in psi with the circular cross section. 400 lb 200 lb/ft D 2 in. -5 ft- -4 ft-
Determine the minimum allowable height (h) in mm of the beam shown in the figure if the bending stress is not to exceed 20 MPа. 5 kN 2.5 kN/m 80 mm A E D 1.0 m 1.0 m 2 m
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
Consider an 8-m long simply supported T-beam with overhangs loaded as shown below. 200 mm w kN/m 50 mm 50 kN-m 50 kN-m 200 mm 2 m 4 m 2 m 50 mm 1. Determine the location of the neutral axis measured from the top of the beam and the moment of inertia (in mm4) of the section about its neutral axis. Draw the shear and bending moment diagrams. Annotate all relevant values and distances. Determine the magnitude of the maximum negative 2. moment. Determine the minimum allowable strength of the beam in tension and the minimum allowable strength of the beam in compression. 3. Determine the maximum allowable load, w (in kN/m), that can be applied pn the beam. 4. B.
. Determine the maximum bending stress in the beam with the circular cross-section. 400 lb B 200 lb/ft 2 in. |2 ft 5 ft- -4 ft - Figure 5.5.6
Determine the absolute maximum normal stress (in unit of MPa) in the beam with external loadings shown below. The beam has a uniform square cross-section with lateral size a = 0.2 m. Note: (1) the shear and moment diagrams can be calculated by either section method or graphical method; (2) there is a concentrated load at point A and a bending moment at point C. 20 kN w = 20 kN/m Mc = = 80 kN · m || В A¬Q C y 2 m 2 m 2 m
If M = 9.0 kip-ft, find the magnitude of the bending stress at a point 2.72 in. above the bottom surface of the beam. The moment of inertia about the z axis is 124.9 in.4, and the centroid of the section is located 4.7 in. above the bottom surface of the beam. M 2207 psi 1712 psi 2368 psi O 1971 psi O 1860 psi M 1 in. ↑ 6 in. 1 in. 8 in. + | .1in.
A beam is supported and loaded as shown. In the section of the beam between 'A' and 'B', the equation for the resisting bending moment was determined as: M₁ = -6.5x²+50x. Determine the magnitude of maximum resisting bending moment (Mr,max) in the section. Note: Do NOT include units in your answer Answer: AA B