The angular displacement of a body is a function of time and is given by equation : 0= 10 + 31+ 6F, where t is in seconds. Determine the angular velocity, displacement and acceleration when t= 5 seconds. State whether or not it is a case of uniform angular acceleration. [Ans, 63 rad/s ; 175 rad ; 12 rad/s']

The angular displacement of a body is a function of time and is given by equation : 0= 10 + 31+ 6F, where t is in seconds. Determine the angular velocity, displacement and acceleration when t= 5 seconds. State whether or not it is a case of uniform angular acceleration. [Ans, 63 rad/s ; 175 rad ; 12 rad/s']

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 3 The rotational speed of a control device decreases from 2000rev/min to 500rev/min in the manner shown below over a 6 second interval. Determine the total number of revolutions N through which the device turns during the 6 seconds. Also find the angular acceleration a in rad/s² during the last 2 seconds of the interval. [Answer: 141.66 rev -26.16 rad/s2] Rev/min 2000 1000 500 Fig Q3 2 Time (s)
The kinematic equation of a material point motion along a straight line (x- axis) has the form x = A + Bt + Cr, where A = 4 m, B = 2 m/s. C= -0.5 m/s? For the moment of time t| = 2 s, determine: 1) the x1 coordinate of the point, 2) the instantaneous velocity V1, 3) the instantaneous acceleration al
A pulley is accelerated uniformly from rest at a rate of 8 rad. After 20 (s) the acceleration stops and the pulley runs at constant speed for 2 minutes, and then the pulley comes uniformly to rest after a further 40 (s). What is the total angular displacement made by the pulley in radians?
A mechanic changing a tire rolls a wheel along the ground towards the car. The radius of the wheel is 42cm, and the speed of the wheel as it rolls is 2 revolutions per second. Height Above Ground (m) radiu HIDE wheel spet Time The diagram above illustrates the vertical motion of a point on the tire over time. It is possible to model the height of this point using a sinusoidal function of the form h(t)=-a sin[b(t-c)]+d. a) Determine the length of time required for one revolution of the tire. b) State the numerical value for each of the parameters a, b, c & d. And write a function representing the motion of the point in the form h(t)= -a sin[b(t−c)]+d.
The slotted disk rotates about point O with a constant rate of w(t) = 5m [rad/s]. Slider A oscillates in the slot with it's position given as x(t) = 25sin(4t) where x is in [mm] and t is in [s). Find the acceleration of slider A whenx = 25 mm. 0(1) x(1) Your answer: -1025i mm/s? -1806.2i mm/s? -3612.5i mm/s? -1112.5i mm/s? -2050i mm/s? -556.25i mm/s?
1. The wheel starts rotating from rest, 4) if its angular velocity W as a function of angular position 0 is w=0.1-0², where O is in radian, and its radius ris 0.2 m, what is the magnitude of the normal linear acceleration (in m/s2) of point Pafter the wheel has turned 1.1 revolution(s) from rest. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Your Answer: Answer
For the following mechanism, if the length of rod AB, /= 2.5 m, and its angular velocity W = 7.6 rad/s, determine the magnitude of the angular velocity of rod AB. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. B 45° Your Answer: Answer 1 units 0.5 m A 30°
1. The wheel starts rotating from rest, 5) if its angular velocity W as a function of angular position is w=0.2-0², where 0 is in radian, and its radius ris 0.3 m, what is the magnitude of the total linear acceleration (in m/s2) of point P after the wheel has turned 1.4 revolution(s) from rest. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Your Answer: Answer P
23. The tip of the pointer of a tower clock moves at a speed of 2 mm/s. Determine the length, the angular velocity, and the centripetal acceleration of the pointer. [Length 1.146 m, angular speed. 1.745E-3 rad/s, centripetal lock. 3.49E-6 m/s²]
1. The wheel starts rotating from rest, is w=0.1.0², where 1) if its angular velocity W as a function of angular position is in radian, and its radius ris 0.2 m, what is the magnitude of the linear velocity of point Pafter the wheel has turned 1.5 revolution(s) from rest. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. Your Answer: Answer P units
es and Machines [Monday 18th - Sunday, 24th] (page 4 of 10) – Google Chrome ne.gmit.ie pages MIT TECMOLADO GALE n A tree feller cuts off large tree near the ground level and then continues to hoist the trunk. If the tree has a mass of 3 tonne (i.e. 3 metric ton), for the position shown 180 C B 1080 2250 2040 720 Determine in meters the vertical distance between pin A and C Answer: Next page
The figure applies to the next questions. There is a body segment with up to three forces applied: proximal, distal, and external. In the coordinate system shown, the acceleration is [1, O, 0] m/s2, and the angular acceleration is 1 rad/s2 about the z axis. The mass is 1 kg, and the moment of inertia is 1 kg-m2. The proximal force is [0, 1, 0] N, and the proximal moment is 0 N-m. The grid has equal spacing 1 cm. 1 cm proximal COM distal If inverse dynamics is performed in the proximal-to-distal direction and, what is the reaction force exerted by this body segment on the distal body segment? A) [1; 0; 0] N B) [0; 1; 0] N C) [-1; 1; 0] N D) [2; 0; 0] N