The analog signal xa(t) = e(120xt-) +e-(180xt-;) is sampled at F, = 300 Hz. What is the expression for the resulting discrete time signalr[n]? а. 2sin(-)b. sin()С. (2тп )5-0.5 sind. 0.5 sin( 2m)5е. —2 sin( 2mп5f. - sin()2nn– sin

Answered: Image /qna-images/answer/563397a5-74a3-4cc8-a008-b433b5ab5fb2.jpg

Answered: The analog signal x.(t) = e(120t-) +e…

The analog signal x.(t) = e(120t-) +e 3(180zt-) is sampled at F, a[n]? = 300 Hz. What is the expression for the resulting discrete tim

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ASAP
The frequency of an analog signal is 23 MHz. What is the minimum sampling frequency for representing it in digital form, according to the Nyquist theorem? Explain with the help of a diagram what happens if Nyquist theorem is not obeyed.
(b) A Digital Signal Processing system, with a 16-bit uniformly quantising analogue-to- digital converter and a sampling rate of 20 kHz, is used to process analogue signals band- limited to the frequency range 0 Hz to 5 kHz. Estimate the maximum achievable signal- to-quantisation noise ratio (SQNR) for sinusoidal input signals, and state what assumptions it is reasonable to make about the statistical and spectral properties of the quantisation noise.
[Q2] Illustrate the signal waveforms of PAM, PWM, and PPM in simple drawings. [Q3] Suppose (t) has the spectrum in the figure below, where f = 550kHz and € = 460kHz. Sketch Xs(f) for f. = 1.6MHz if ideal sampling is considered. X(f) AÏN -f f₁ + E 0 fu
How does duality facilitate the transformation between time and frequency domains in signal processing?
i)Most electronic circuits in communication are used to process signals which can be in digital oranalogue form. These circuits are manned for manipulating signals towards producing a desiredresult. Generally, all signal processing circuits will engage with two main factors. Identify thesefactors and compare their role in communication. A) Electronic and OpticalB) Wireless and Free SpaceC) Analog and DigitalD) Gain and NoiseE) Noise and AttenuationF) Gain and AttenuationG) None of the above ii)Signals travel in communication channels are always exposed to the possibility of interferenceeffect that could destroy the transmitted information. The interference occurs due to the existenceof two or more frequencies. There is a component that limits specific range of frequencies andallows other range to pass through in the channel. Identify this component and explain its operationwith aid of diagram. A) ModulatorB) BasebandC) Local OscillatorD) Electrical CouplerE) Optical SwitchF) Bandpass…
Compute the eight-point DFT of the sequence x(n) using radix-2 decimation-in-time. Follow exactly the corresponding signal flow graphs and keep track of all the intermediate quantities by putting them on the diagram. x(n)=1/2.sin(pie/4.n),0<=n<=?
please answer with solution. An analog signal with a bandwidth of 36MHz is sampled at a frequency (fs) of 72,000,000 samples per second during the ADC (analog-to-digital conversion) process. What is the outcome of the received signal after the DAC (digital-to-analog conversion) process? a. the signal will have experienced aliasing b. the signal will not experience aliasing c. the signal will not experience quantization errors d. none of the above describes the outcome
Q₁: ph paper when required. A-The analog signal s(t) = 10 cos (20 pi*t) cos (200 pi*t) is sampled at the rate of 250 samples per seconds. Determine the following: a- The maximum frequency component present in the analog signal. b-Nyquist rate. B- An analog signal having single frequency as 3 kHz is sampled with 5 kHz signal. Describe its frequency spectrum. What will be the output if the sampled signals are passed through a low-pass filter having cutoff frequency at 2.5 kHz?
c) Draw the spectrum of the sampled signal when the sampling rate is equal to 2.5 x 10* An analog signal given by: x(t) = sinc?(10*t) is sampled using an ideal sampling technique. a) What is the Nyquist rate of this signal. b) Draw the spectrum of the sampled signal at the Nyquist rate. ) Draw the spectrum of the sampled signal when the sampling rate is equal to 1x 10 sample/sec. sample/sec.
Draw the spectrum of the sampled signal when the sampling rate is equal to 2.5 × 10* d) Draw the spectrum of the sampled signal when the sampling rate is equal to 1× 104 Draw the spectrum of the sampled signal at the Nyquist rte. An analog signal given by: x() = stn'(104) %3D is sampled using an ideal sampling tchnique. a) What is the Nyquist rate of this signal. Samplesec. the samplekse,
Problem 4: Two lowpass signals each band limited to 3 KHz are to be time multiplexed into a single channel using PAM. Each signal is impulse sampled at frequency of 50% above the Nyquist frequency. The time multiplexed signal wave form is filtered by an ideal LPF before transmission. f1(t) LPF PAM Signal Sampler f2(t) LPF Pulse Clock Gen. a. What is the minimum clock frequency of the system? b. What is the minimum cutoff frequency of the LPF? In the receiver, the signal is impulse sampled and demultiplexed using the system shown, determine the minimum and maximum acceptable BW of the LPF used in retrieving the analog signals.