The A992 structural steel bar and a 2014-T6 aluminium bar shown below are secured to rigid supports at ends A and B and are connected together by a 1" diameter tool steel pin in double shear. The pin slides freely into place at room temperature. Determine the shearing stress on the pin caused by a 60 degree F drop in temperature and comment on its ability to carry the applied load.

The A992 structural steel bar and a 2014-T6 aluminium bar shown below are secured to rigid supports at ends A and B and are connected together by a 1" diameter tool steel pin in double shear. The pin slides freely into place at room temperature. Determine the shearing stress on the pin caused by a 60 degree F drop in temperature and comment on its ability to carry the applied load.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.2.1P

See similar textbooks

Similar questions

Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
2) Find the axial stresses of menbers FD, GD, GE State if it is tensile or Compressive. 4M 3M A LE 3m G 20 RN Go KN
The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the minimum pin diameter. Use Shear stress-D0.4"Yield strength. Assume material is 1020 hot-rolled steel. * P2 Shear Planes Pin
The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. E200 CPa E1m 2.0 m 0.6m 1.5 m VP-20 KN Aluminum E-70 GPa A=900mm2 L-1.5 m What is the axial stress at steel rod in MPa?
4 A flanged bolt coupling has ten 12-mm di ameter steel bolts on 500 mm diameter b olt circle and six 16 mm diameter aluminu m bolts on 300 mm diameter bolt circle. T he maximum shear stresses of the materi als are 60 MPa in steel and 40 MPa in al uminum. Use G = 80 GPa for steel and 3 0 GPa for aluminum. What is the maximu m required shear strength of each alumin um bolt to determine the maximum torqu e that can be applied to the system? Dra wing not included in this problem.
2- A 2m COPPER BAR SUBJECTEO TO A TENSILE IS SUSPENDED FROM A LOAD IBO KN SUPPORTED BY TWO IDENTICAL PIN THAT S pOSIS AS SHON OF THE LOWER AFPLIED TENSILE POSTS SUPPORT THE STEEL DETERMINE THE TOTAL DEFORMATION END OF THE LOAD HINT: NOTE THAT THE STEEL PIN WHERE THE COFPER BAR IS ATTACHED. COPPER BAR DUE TO STEEL POST L=0.5m A= 4500mm E- 200GPA COPFER BAR L- am A= 4800 Mn E- l20 GPa 180KN
Situation 5. The angular section shown below is welded to a 12 mm gusset plate. Both materials are A36 steel with Fy = 250 MPa. The allowable tensile stress is 0.6Fy. The weld is E80 Electrode and 12 mm thickness. INNOVATIONS Properties of L 150x90x12: y = 50 shear stress of weld = 0.3Fu A = 2750 Allowable REVIEW INNOVATIE a K ➜ www A. 234 KN B. 349 KN b 13. What is the value of P without exceeding the allowable tensile the angle? C. 382 kN p. 413 kN 14. Find required length of the weld based on shear? A. 280 mm C. 300 mm D. 380 mm B. 320 mm 15. Find the required value of a? A. 108 mm B. 97.9 mm D. 185 mm NEW INNOVATIONS REVIEW INNOVATIOf REVIEW NEW INNOVATIONS
Maxinnun allowable stress for steel - 140 MPa Maxinnum allowable stress for ahuminum = 90 MPa Maxinnun allowable stress for brouze - 100 MPa Required: Maximun safe value of axial load P Aluminum A 400 mm Bronze A= 200 mm Steel A= 500 mm 2P 4P 2.5 m 2.0 m 1.5m
A flexural member is fabricated from two flange plates 1/2 x 16 and a web plate 1/4 x 20. The yield stress of the steel is 50 ksi.
The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a 304 stainless steel rod EF having a diameter of 40 mm, and a rigid member G. If the supports at A, C, and F each have a stiffness of k= 200 MN/m determine the average normal stress developed in the rods when the load is applied. A C -300 mm- 30 mm 30 mm B D G E 450 mm 40 kN 40 kN 40 mm F
8. The assembly consists of a steel bar A (Ast= 500 mm2, Est= 200 GPa, and aAL= 12 x 10-6), a rigid block C, and a bronze bar B (ABR= 2000mm2, EBR= 100GPA, and aBR= 18 x 10-6) securely fastened together to rigid supports at the ends as shown. Initially, there is no stress in the members. The temperature drops 25°C, and the load P of 200kN is applied. Determine the maximum normal stresses in A and B for this condition. P/2 P/2 0.5m
The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the temperature is 30°C, the gap between the rod and rigid member AE is 0.1 mm. Assume BF is also rigid. (Figure 1) Figure 400 mm A B 25 mm 50 mm D 0.1 mm 300 mm E 1 of 1 25 mm Part A Determine the normal stress developed in the bolts if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. of = Submit Part B σ₁ = Submit O HA Value Request Answer Provide Feedback ■μÅ Value Determine the normal stress developed in the rod if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units Request Answer wwwww Units ? wwwww Review ? Next >