Answered: The _____________________ of…

The _____________________ of transformers are neglected to draw the reactance diagram. a-Shunt branches b -Series conductance c-Series reactance d-Static Loads

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33MCQ: The direct electrical connection of the windings allows transient over voltages to pass through the...

See similar textbooks

Related questions

Q: The recommended limit of voltage drop on a power circuit for a single-phase supply as per IEE Wiring…

A: The explanation is as follows.

Q: draw and explain service connection wiring diagram for 1 phase and 3 phase installation

A: Rules For Wiring : The current Rating of wire should be 1.5 times the load current Required For…

Q: Larger conductors should be used for long runs to minimize the? A. Current B. Voltage drop c.…

A: for the long runs the larger conductors are generally used.

Q: .A 33 KV line has a resistance of 4 ohm and reactance of 16 ohm respectively. The line is connected…

A: Given R=4 ohm X=16 ohm Let 10000 KVA be the base KVA Reactance of generator 1 Xg1=10 %…

Q: 2- Why it's imporctical carry out actual load test on large rating transformers ?

A: Since 2 and 3 are two different questions, as per the guidelines, only the first question (2) has…

Q: What was the effect of neutral wire removal in balanced and unbalanced 3-phase circuit?

Q: What is the purpose of plenum-rated cabling?

A: In this question of we will write purpose of plenum rated cabling...

Q: compare between electrification of residential and commercial installationf

A: Compare between electrification of residential and commercial installation 1. Typically, commercial…

Q: If required, what type of diagram must indicate the calculated load, demand factors, conductor type…

Q: Three single-phase transformers, each rated 10 MVA , 66.4/12.5 kV, 60 Hz , with an equivalent series…

A: Calculate the per unit current with respect to the base.

Q: Figure shows a sample power system network and Zpus Matrix elements. For a solid three phase fault…

A: Note: Here line impedance as well as Z bus matrix impedance are given We are going to solve the…

Q: The positive-, negative-, and zero-sequence reactances of a 15-MVA, 11-kV, three-phase, wye-…

A: Given data about a three phase, wye-connected generator is, Positive sequence reactance X1=11%=j0.11…

Q: 8.In a line-by-line failure we can expect Immersive reader A) Currents exist in the ground…

Q: 9. Which grounding method is typically required of higher-voltage systems? A. Grounding through…

A: In this question, We need to choose the correct options Which grounding method is typically…

Q: Why is zero sequence impedance important in Zigzag transformers and grounding transformers

A: Why is zero sequence impedance important in Zigzag transformers and grounding transformers?

Q: For large power transformers rated more than 500 kVA, the winding resistances, which are small…

Q: Draw the reactance diagram of the given one-line diagram below marked in appropriate per unit…

A: There will be three sequence networks in the given power system- Positive-sequence network…

Q: b) A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout…

A: POWER SYSTEM: A power system is a network of electrical components that provide, transmit, and…

Q: The single-line diagram of a three-phase system is given in Figure 3. The three-phase generator is…

A: Given: The ratings of each element are as follows: Generator-4.16 MVA, 2.4 kV, 1000 A.Transformer…

Q: Where nonmetallic-sheathed cable is run at angles with joists in unfinished basements, it shall be…

A: According to article 334 nonmetallic -sheathed cable . Where nonmetallic-sheathed cable is run at…

Q: Draw the reactance diagram, with all reactance's marked in per-unit. Select the 100 MVA and 25kV as…

A: In this question we need to draw a reactance diagram of the given single line diagram.

Q: Which one of the following diagrams shows delta-delta connections of three single-phase transformers…

Q: 3. A 100 MVĂ, 33KV 3-phase alternåtör current are as under: 3-phase fault-2000A, Line to Line…

A: Please refer the attached images for the complete answer..

Q: What is the per unit impedance of a 50 MVA, 13.8 kV, 1% impedance transformer if the base is change…

Q: You are given that the system shown in Figure 4.25 has a 110/220 kV autotransformer. The positive-…

A: Since there is single line to ground fault in phase a. So, fault current in phase a will be IF and…

Q: A 300-kilovolt-ampere transformer bank consisting of three 100-kilovolt-ampere transformers has a…

Q: Figure below shows a power system where load at bus 5 is fed by generators at bus 1 and bus 4. The…

A: 1) When base voltage is changed to 11 kV, change in fault current ? 2)

Q: capacitors will supply reactive VAR during peak load condition and consumes reactive VARs during…

A: 1.Booster Transformer:-It is used at the end of a power line or at the intermediate position to…

Q: Three single-phase two-winding transformers, each rated 3 kVA, 220/110 volts, 60 Hz, with a 0.10…

A: Given data for single phase 2 winding transformer S =3 kVA, Voltage ration =220/110 volts, Frequency…

Q: 3) The single-line diagram of a three-phase system is given in Figure 3. The three-phase generator…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: 16. Which of the following are sometimes installed as an emergency system, legally required standby…

A: Choose the correct option Which of the following are sometimes installed as an emergency system,…

Q: What happens when the sag in an overhead transmission line increases? How the sag varies when the…

A: The vertical distance between the points of consecutive supports and the lowest point of the…

Q: explain why Transformers are necessary in all stages of power distribution systems. Three-phase…

A: Given: Transformer: Transformer is a static device used for the transfer of varying voltage and…

Q: In Ring main system, the primaries of distribution transformers form a loop. The loop circuit starts…

A: We need to tell about the given statement is true or false.

Q: 7. Which of the following are sometimes installed as an emergency system, legally required standby…

A: In this question, Choose the correct option Which of the following are sometimes installed as an…

Q: 3-phase, 33-MVA, 44-kV alternator has a substransient reactance of 7%. A 3-phase short circuit…

A: Given s=33-MVAV=44-KVsubtransient reactance=7%=0.07P.U

Q: Draw the connection diagram for two parallel transformers with (Δ-Δ) connected ?

A: Connection diagram of two parallel transformer connected in delta :

Q: When the feeder ring is energized by two or more than two generating stations or substations, the…

A: We need to tell about the given statement is true or false.

Q: 3. Why the percentage impedance drop of the transformers are kept equal during the parallel…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 4_ What measures and procedure would you perform in order to detect a missing/disconnected phase in…

A: When a phase is missing or disconnected from a 3 phase power system, this type of failure is called…

Q: Consider the system shown in the single-line diagram of Figure (3). All reactances are shown in per…

A: Three phase fault is symmetrical fault, hence fault study can be done on per phase basis. All the…

Q: A В C D

A: (a) Protection scheme of one of the transformers connected in parallel. parallel transformer are…

Q: In Back To Back Test on Two Similar Single Phase transformers. What will be the current in the…

Q: Draw the reactance diagram of the given one-line diagram below marked in appropriate per unit…

Q: A star connected 3-phase 10 MVA, 6.6 kV alternator is protected by circulating current protection,…

A: In this question , we will find value of earthing resistance required if 85% of stator winding is…

Q: Example-1: In a single-loop distribution system shown in the figure consider the generator to be of…

A: A) Given fault is L-L fault:Ip=3×ER1X1eq+X2eqIp=3×1.0X1eq+X2eqAt…

Q: what is substation ? what is powergrid? is switchyard safe?

A: The electrical power distribution system consists of the following parts : Generating stations…

Q: _____________________ of transformers are neglected to draw the reactance diagram. -Series…

A: Fill the blank

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

The _____________________ of transformers are neglected to draw the reactance diagram.

a-Shunt branches

b -Series conductance

c-Series reactance

d-Static Loads

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False
Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
In per-unit equivalent circuits of practical three-phase transformers, under balanced thr-phase operation, in which of the following connect ions would a phase-shifting transformer come up? (a) Y-Y (b) Y- (c) -
Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.
Consider a bank of this single-phase two-winding transformers whose high-voltage terminals are connected to a three-phase, 13.8-kV feeder. The low-voltage terminals are connected to a three-phase substation load rated 2.0 MVA and 2.5 kV. Determine the required voltage, current, and MVA ratings of both windings of each transformer, when the high-voltage/low- voltage windings are connected (a) Y-, (b) -Y, (c) Y-Y, and (d) -.
Three single-phase two-winding transformers, each rated 25MVA,54.2/5.42kV, are connected to form a three-phase Y- bank with a balanced Y-connected resistive load of 0.6 per phase on the low-voltage side. By choosing a base of 75 MVA (three phase) and 94 kV (line-to-line) for the high-voltage side of the transformer bank, specify the base quantities for the low-voltage side. Determine the per-unit resistance of the load on the base for the low-voltage side. Then determine the load resistance RL in ohms referred to the high-voltage side and the per-unit value of this load resistance on the chosen base.
1.a. For performing dielectric-strength tests on insulating materials, two transformers are connected in aA. parallel combination.B. cascade arrangement.C. polyphase arrangement. 1.b. In large power transformers, the unequal voltage distribution caused by voltage surges in the winding isprevented by the use ofA. static shields.B. series capacitors.c. low-voltage arresters.
Describe the On-load and No-load in transformers
The _____________________ of transformers are neglected to draw the reactance diagram. -Series conductance -Series reactance -Static Loads -Shunt branches
Name two types of Transformers equivalent circuit and then compare them.
2- Draw and explain the phasor diagram for two transformers in parallel.
Connect three single-phase transformers in Y-Y, with subtractive polarity, so that the line-to-line voltages on the primary are 30 degrees delayed to their respective line-to-line voltages on the secondary. It should show each step that is needed to make this connection (example: the phasor diagram) and should show the final connection of the three transformers including the polarity markings. Assume phase A on the primary is terminal "H1".