Suppose you're riding your bicycle in the mountains. You climb a mountain pass on a scenic roadway and prepare to descend the other side of the mountains. You have a choice of two roads you can use to descend. One road is two miles long, while the other is ten miles long. Assuming you apply the same, consistent braking force throughout the duration of your descent for either route, which descent route will allow you to reach the base of the pass with the highest speed? Two-mile (shorter) route Ten-mile (longer) route No difference

Suppose you're riding your bicycle in the mountains. You climb a mountain pass on a scenic roadway and prepare to descend the other side of the mountains. You have a choice of two roads you can use to descend. One road is two miles long, while the other is ten miles long. Assuming you apply the same, consistent braking force throughout the duration of your descent for either route, which descent route will allow you to reach the base of the pass with the highest speed? Two-mile (shorter) route Ten-mile (longer) route No difference

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A force Fis said to be conservative if the work done is independent of the path followed by the force acting on a particle as it moves from A to B. depends only on the initial and final positions of the particle is independent of its velocity or acceleration. all of the above does not depend on the initial and final positions of the particle.
A block is pulled at constant speed along a rough level surface by a ropc that makes an angle of 30° with respect to the horizontal. The applied force along the rope is P . The force of kinetic friction between the block and the surface is 20 N. 30° Which one of the following expressions gives the magnitude of the force P in SI units? O 20(sin 30°) O 10(cos 30) O tan 30 O 20/(cos 30) O 30/(sin 30°) O O O O O
b) Determine the average power required for a 1000 kg car to climb a 150 m long incline slope of 30° in 30 seconds. Assume there is no drag, rolling resistance on the car during your analysis, calculate the following conditions: i. Climb at a constant velocity; ii. From an initial state of rest to a final velocity of 50 m/s; ii. From an initial velocity of 25 m/s to a final velocity of 10 m/s.
A truck weighing 5 kips is traveling with a constant velocity of 50 mph when brakes are applied causing a braking force of 2 kips. If the truck is going up a road inclined at 100, Proove that the distance traveled before it stops is 176.17 feet.
Khufra works at a spring factory and he was assigned to test a certain spring, whose constant is 50 N/m attached to a 50-kg block in an incline (©=30°). With the spring initially at equilibrium position, the block was pushed 0.3 meters up the incline by a 50-N external force applied parallel to the path. The coefficient of kinetic friction is 0.30. d) How much work is done by the block (in Joules) on the spring? e) How much work is done by the applied push on the block? f) How much work is done by friction?
2 Your friend is planning to ride his bike up a ramp and land on the roof of a building as shown below. The building is 6.00 m high and 8.00 m away from the ramp. The ramp is 3.00 m wide and 4.00 m tall. 4.00 m 1 ← 3.00 m 6.00 m 8.00 m A. What is the minimum speed with which your friend needs to leave the ramp in order to land on the building? B. Another friend is going to use his motorized scooter for the same stunt. The maximum speed of the scooter is 15.0 m/s. How close to the building should you move the ramp so that your friend lands on the roof right at the front edge of the building?
Blocks of granite are to be hauled up a 15° slope out of a quarry and dirt is to be dumped into the quarry to fill up old holes. To simplify the process, you design a system in which granite block on a cart with steel wheels (weight w1, including both block and cart) is pulled uphill on steel rails by a dirt filled bucket (weight w2, including both dirt and bucket) that descends vertically into the quarry. How must the weight w1 and w2 be related in order for the system to move with constant speed? Ignore friction in the pulley and wheels and ignore the weight of the cable.
1. A 25kg boy is riding a merry-go-round with a radius of 5m. What is the centripetal force on the boy if his velocity is 6 m/s?
The shoes of a person playing ice skating experiences Select one: Both static and dynamic friction O Sliding Friction Rolling Friction O Static Friction
A great pianist is getting ready for his concert and plan to move his exclusive grand piano to his concert venue. The 700 kg piano needs to be loaded onto a truck bed which is about 1.5 m high.1.Initially, the movers decide to use an adjustable ramp to move the piano. The ramp can only be adjusted up to 10 m long and the inclination angle must not exceed 20° to ensure a safe loading process. Determine the range of a suitable length and angle of the ramp. 2.On a second thought, the movers are considering whether it is easier to lift the piano straight up onto the truck bed or push it up along the rough the ramp. With the aid of an appropriate free body diagram, justify the most efficient option for the movers to load the piano to the truck bed with constant speed. State clearly all the assumptions made, and the principles used in the calculations to support your answers.
A block is pulled along a rough level surface at constant speed by the force P. The figure shows the free-body diagram for the block. FN represents the normal force on the block; and / represents the frictional force. If the coefficient of kinetic friction, HR , between the block and the surface is 0.30 and the magnitude of the frictional force is 80.0 N, what is the magnitude of the normal force FN? mg OA 410 N OB 160 N OC 1.6 N OD.4.0 NA OE 270 N
A crane is lifting a system with a constant speed. The weight of each object is shown. Neglect the mass of the cables. Note that K stands for Kipps [1K = 1,000lbs] and is a unit of force. Do NOT convert or multiply by g. cable 1 How many forces are acting on the ring? 4. ring (2K) 6 How many forces are acting on the spreader bar? cable 2 cable 3 How many forces are acting on the load? 3. 45° 45° Are the forces on the system balanced? yes v spreader bar (20K) cable 4 cable 5 How much tension in is cable 1? K How much tension in is cable 2? K load (48K) BARNHART K How much tension in is cable 3? K How much tension in is cable 4? K How much tension in is cable 5? check answers'