Suppose a monatomic ideal gas is changed from state A to state D by one of the processes shown on the PV diagram. 1. The gas follows the constant-temperature path AC followed by the constant-pressure path CD. What is the total work done on the gas ? What is the total change in internal energy of the gas during the entire process?  What is the total heat flow into the gas?

Q: Part A At extremely low temperatures, the specific heats of metals are proportional to the absolute…

A:

Q: In the graph below, each unit on the horizontal axis is 3.0 m and each unit on the vertical axis is…

A:

Q: An ideal monatomic gas is held in a perfectly insulated cylinder fitted with a movable piston. The…

A: Given data The initial pressure of the gas is: P1 = 110 kPa The initial temperature of the gas is:…

Q: One and one-half moles of an ideal monatomic gas expand adiabatically, performing 9600 J of work in…

A: number of moles = 1.5 work done = 9600 J process=  adiabatic

Q: A monatomic ideal gas undergoes the thermodynamic process shown in the PV diagram at the right.…

A: Area under P-V graph gives the total work done. Ideal gas equation is PV=nRT Change in internal…

Q: Question2: A monatomic ideal gas initially at p=1.50 x105 Pa and V=0.0800 m3 is compressed…

A:

Q: Part B A container holds a sample of ideal gas in thermal equilibrium, as shown in the figure.…

A: B) Vol will decrease Temp will be same  The piston does work on the gas, which, if the container…

Q: 13 moles of monatomic ideal gas undergoes a thermodynamic process from point a to point c, as shown…

A: Given, P1=4.0×105 PaP2=2.0×105 PaV1=0.002 m3V2=0.003 m3V3=0.004 m3 From point a to b the temperature…

Q: When a gas expands adiabatically in a tank, it does work on its surroundings. But if no heat flows…

A: In an adiabatic process the interaction of heat with the system is restricted. In the adiabatic…

Q: The temperature at state A is 20°C, that is 293 K. What is the heat (Q) for process A to D, in MJ…

A:

Q: s the change in internal energy of the gas? (ii). How much work was performed by the gas? (iii).…

A: Given:- The mole n= 5  The volume V1 = 29 L  The volume V2 = 34 L  The constant temperature T = 300…

Q: AT = K Ideal-gas processes are often shown on a pV diagram that graphs pressure versus volume.…

A: Given Initial Volume V1 = 50 L = 50 × 10-3 m3  Final volume V2 = 150 L = 150 × 10-3 m3  Initial…

Q: What if the actual work done (more realistically) is W = 320 J during a single cycle; what is the…

A:

Q: A gas is taken through the cyclic process shown in the attached figure. (a) Find the net energy…

A: (a) Calculation: The change in the internal energy in a cyclic process is zero. The work done in the…

Q: A gas follows the PV diagram in the figure below. Find the work done on the gas along the paths AB,…

A:

Q: A gas follows the PV diagram in the figure below. Find the work done on the gas along the paths AB,…

A:

Q: What is the heat delivered to the gas for process #2 (the diagonal line process) as illustrated on…

A: In the given question, the gas goes through a cyclic process consisting of processes 1, 2 and 3.…

Q: how to answer part a

A: Given,

Q: The PV diagram below represents a gas that expands from point I to point F along the three different…

A:

Q: 8.2 moles of an ideal monatomic gas expand adiabatically, performing 8000 J of work in the process.…

A:

Q: Figure shows a pV-diagram for an ideal gas in which its absolute temperature at b is one-fourth of…

A: Given, PV-diagram for an ideal gas Va = 0.500 L Tb = Ta4 Pb = Pa = 1.50 atm

Q: Three moles of an ideal gas undergo a reversible isothermal compression at temperature 19.0 °C.…

A:

Q: a) IAF   You may have entered the work done by the gas on the environment instead of the work done…

A: a) For the path IAF, the work done on the gas can be determined as, Here, WIA and WAF represent the…

Q: A gas expands from I to F in the figure below. The energy added to the gas by heat is 252 J when the…

A: Given, heat given to the gas for process I to F diagonally isQIF=252J    Pressure at I is PI=4…

Q: .7 moles of an ideal monatomic gas expand adiabatically, performing 8800 J of work in the process.…

A: Solution :  Given that            Number of the moles of the mono-atomic gas (n) = 8.7…

Q: The temperature at state A is 20°C, that is 293 K. What is the heat (Q) for process D to B, in MJ…

A:

Q: The fpicture shows a pV diagram for an ideal gas in which its pressure tripled from a to b when 804…

A: Heat given to gas Q = 804 J The graph between P and V is shown . We need to determine work done.

Q: An ideal gas is taken from a to b on the pV diagram shown in the figure.  During this process, 700 J…

A:

Q: One and one-half moles of an ideal monatomic gas expand adiabatically, performing 7100 J of work in…

A: The process is adiabatic, so there is no heat energy. Since, the process is adiabatic expansion,…

Q: A gas sample undergoes the cyclic process ABCA shown in the figure (Figure 1), where AB lies on an…

A: For adiabatic process PVr =constant

Q: respects except that one contains diatomic gas and the other a monoatomic gas. Both cylinders…

A: The adiabatic process equation: PVγ = constant   Where, P is the pressure of the system V is the…

Q: One method of converting heat transfer into doing work is for heat transfer into a gas to take…

A:

Q: Thermodnamics At 25 °C 1 mol of an ideal gas is expanded isothermally from 2 to 20 dm3. Calculate ΔA…

A:

Q: Part A Ideal-gas processes are often shown on a pV diagram that graphs pressure versus volume.…

A: Given data: Number of moles, n=2 mol Initial pressure, P1=100 kPa=100×103 Pa Initial volume, V1=50…

Q: (a) What is the unit of "specific entropy"? Is it an extensive property? (b) What is an isentropic…

A: Entropy refers to the measure of randomness of any system. Specific entropy is entropy per unit…

Q: A heat engine is run between two reservoirs at temperatures TH and Tc. One cycle of this engine…

A: Since you have asked multi subpart question, I am answering first 3 subparts. If you need the answer…

Q: (a) If tossing 100 coins, how many ways (microstates) are there to get the three most likely…

A: The number of microstates to get 49 heads and 51 tails = 9.9×1028 The number of microstates to get…

Maxwell speed distribution

Maxwell-Boltzmann distribution or commonly known as Maxwell speed distribution, explains the division of the energy levels of the molecules of an ideal gas on the basis of the statistical theory. In 1859, Scottish physicist James Clerk Maxwell established the context for the distribution of molecular velocities for random molecules moving in a closed environment. This theory was generalized in 1871 by German physicist Ludwig Boltzmann. He improvised the theory to express the distribution of energy levels among different molecules.