: A rectangular beam has a width of 350 mm, and effective depth d=570 mm to centroid of tension steel bars. Tension steel reinforcement consist of 6032mm in two rows, compression reinforcement of 34025mm. Calculate the design moment strength of the beam, where f'c-35 Mpa, fy=420 Mpa. (Mu-911 kN.m Ans)

: A rectangular beam has a width of 350 mm, and effective depth d=570 mm to centroid of tension steel bars. Tension steel reinforcement consist of 6032mm in two rows, compression reinforcement of 34025mm. Calculate the design moment strength of the beam, where f'c-35 Mpa, fy=420 Mpa. (Mu-911 kN.m Ans)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5- A beam is reinforced with Ø16 mm bars and Ø10@200 mm stirrups. If the concrete cover is 40 mm, f, = 420 MPa and f' = 25MPA , then the development length of the 180° hooks of the reinforcing bars is .....mm. (a) 573 (b) 323 (c) 269 (d) 430 (e) None
Bearing P plate Let the allowable stresses in the post be ost=120MPaand oco=6MPA. Compute the maximum safe axial load P that may be applied. The moduli of elasticity are 200 GPafor steel and 14 GPafor a concrete. Each steel bar has cross-sectional area of 900mm2. Steel - Concrete - 300 mm 300 mm
Check the adequacy of the isolated T-beam shown below according to ACI Code requirements and determine the design flexural strength (Moment) for it, use: • f = 20 MPa. • fy = 420 MPa. Effective depth d = 610 mm. • Reinforcement is 6Ø25mm (ABar = 490 mm?). 500 mm 125 mm 700 mm 6Ø25mm 250 mm
the T-beam is reinforced with an unbonded tendon having an area Aps=1000 sq. mm., fc'=35 MPa, Fpu= 1800 MPa, Fpy= 1620 MPa and the effective stress after losses is Fpe= 1100 MPa. The beam has a simple span of 6 m, b= 2500 mm, hf= 80 mm, bw= 300 mm, dp= 800mm and h= 900 mm. Compute the stress in prestressed reinforcement at nominal strength. Compute the depth of compression block. Compute the moment capacity of the beam.
AT:Design the steel reinforcement for flexural for the beam shown in the kN fig.below The dead load on the beam is 100 (not include self weight) & the live load is 200KN. useØ25mm& Use effective cover in top& bottom=60mm, use fc' = 27.6 Mpa, fy= 414Mpa. Ptive=200KN kN D.L= 100 d= 550mm 275mm 3m Зт
2 A simply supported beam has a dimension of 300mmw x 600mmh has a span of 6m. it has a superimposed load of 30KN/m and live load of 50KN. It has a specified concrete strength of 28MPa and yield strength of 420MPa. Distance of centroid steel area to outermost fiber is 60mm. a. What is the maximum moment of the beam? b. What is the required tension steel area? Use et = 0.004
Calculate the design moment strength for the reinforced concrete beam section shown below. f. = 24 MPa and f, = 415 MPa . 300 mm 5-D28 50 mm di = 812.5 mm
USE NSCP 2010 A simply supported beam is reinforced with 4 – 28 mm ø at the bottomand 2 – 28 mm ø at the top of the beam. Steel covering to centroid ofreinforcement is 70 mm at the top and bottom of the beam. The beamhas a total depth of 400 mm and a widthof 300 mm. fc’ = 30 MPa, fy = 415 MPa. Balanced steel ratio ρb = 0.031.Compute the ultimate moment capacity of the beam in kN-m. Usereduction factor of 0.90
A. Beams Analysis - Determining Moment Capacity for beam (Under-Reinforced, Over-Reinforced, Balanced Conditions) 3 #19 -350 mm- 520 mm 600 mm 80 mm *For the problem above, use f'c = 28MPa and Fy = 414MPa. C. What is the depth of the compression block "a"? d. What is the stress in the steel fs? How about the stress in f's?
The beam shown has the following properties: concrete cover=40mm, ds= 10mm, f'c=21 MPa, and fy=280 MPa. Determine the ultimate moment capacity of the beam in kN-m. Determine also the type of failure and the beam condition (under-reinforced, over-reinforced or balanced condition) 250mm 5-ø16mm h =450mm 50mm
A reinforce d rectangular beam with width b and effective depth d has 4.16 mm bars placed on 1layer at the tension side. The beam has a stirrup with diameter of 10 mm. Use f c'= 28 M Pa and fy = 420 M Pa. Given: b=532.5mm d=877.5mm Fy = 420 MPa F'c = 28 MPa L= 6.35 m Wp=36KN/m WL=47.5kN/m 1.Calculate the nominal moment capacity of the beam. 2. Calculate the strain of the tension bars. 3. Calculate the strength reduction factor of the beam. Activ Go to
10 mm | | | | 10 mm 50 mm ارت - 50 mm 10 mm 20 kN B 150 mm 910 mm 10 kN D ------- 150 mm Two vertical forces are applied to a am of the cross section sh vn. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.