Steam at 11 bar and 250°C enters a convergent divergent nozzle and is expand to 1 bar. Find the throat and exit area and mechanical energy of the jet for a steam flow of 1.0 kg/sec. If the losses due to friction amount to 8%, what is the change in the throat and exit area ? If ontinue question below under these conditions the nozzle section is ame as that for the isentropic flow, what should pe the mass flow rate and mechanical energy of he jet.

Steam at 11 bar and 250°C enters a convergent divergent nozzle and is expand to 1 bar. Find the throat and exit area and mechanical energy of the jet for a steam flow of 1.0 kg/sec. If the losses due to friction amount to 8%, what is the change in the throat and exit area ? If ontinue question below under these conditions the nozzle section is ame as that for the isentropic flow, what should pe the mass flow rate and mechanical energy of he jet.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The diffuser in a jet engine is designed to decrease the kinetic energy of air entering the engine compressor. Clearly define the type of transformation between inlet and outlet. Air enters the inlet at 100 kPa at 20 °C and a velocity of 340 m/s and exits at 350 kPa and Cp ? Calculate the 90 °C. Assume that air is a calorically perfect gas. What is P/c, velocity at the outlet Aout Ain Assume that air is a calorically perfect gas. What is the ratio
A reducing bend with an inlet diameter of 200 mm and exit diameter of 150 mm bends 40 degreesupwards. The water velocity and corresponding pressure at the inlet to the band is 4, 5 m/s and 70 kParespectively. Determine the weight flow, the water flow velocity at the exit to the bend, the bend exitpressure if the friction head loss through the bend section is 2 m and the magnitude and direction ofthe resultant force flowing through the bend.
Please show your complete solution. Thank you! Air flows in a steady flow manner through a converging tube. At the inlet the pressure is 690kPaabs and the density is 0.838 kg/cu.m. If air enters with a volume flow of 125 cu.m per min at the rate of 94 m/min and the exit section has a diameter of 350mm, determine a.) the mass flow rate, kg/min b.) the diameter of the entrance section and c.) the exit velocity. Assume that the density is constant.
Find the velocity of steam issuing from a nozzle in which the steam has been expanded in an initial condition of 10.3 bar absolute dry to a pressure of 0.686 bar (i) neglecting friction and (ii) considering frictional loss as 10 per cent of the heat drop.
Q1: A converging-diverging frictionless nozzle is used to accelerate an airstream emanating from a large chamber. The nozzle has an exit area of 30cm² and a throat area of 15cm². If the chamber temperature is 500K, and the back pressure is 101kPa, calculate the following: a. Minimunt chamber pressure (po) to choke the nozzle. b. Mass flow rate for a chamber pressure (po) of 400kPa. c. Mass flow rate for a chamber pressure (po) of 105kPa.
Q5: A converging-diverging nozzle, which is shown in the figure, is supplied with air from a large tank where the pressure is Po and exhausts to the atmosphere with a pressure of Pt. The area A at distance x from the throat is given by At (1 + 0.75x/L)), where At is the throat cross- sectional area and Lis the total length of the diverging part of the nozzle. At a certain pressure ratio P/Pb, a normal shock wave stands in the nozzle at a point where the Mach number before the shock is 1.7. Find the position of the normal shock wave from the throat, and the (A %3D pressure ratio P/Po. Ans.: 0.45 L= 0.753 P.
As shown in figure Q1, air flows through a converging nozzle from a large tank and into a receiver. At section 1, the temperature is 350 k, the pressure is 320 kPa (abs), and the flow the flow area is 0.40 m?. The pressure in the large tank is 360 kPa (abs). Nozzle exit area is 0.30 m?. Air flow is assumed to be steady and isentropic in the converging nozzle. Express answer at least 3 significant figures. Take K as 1.40 and R as 0.287 kJ/kg.K Determine: a) The mach number at Section 1. b) The mach number, pressure and velocity at the exit. c) The mass flow rate through the nozzle. Large Tank Pressure = 360 kPa (abs) Air flows Nozzle Exit
At the inlet to a certain nozzle the enthalpy of fluid passing is 2800 kJ/kg. In addition, the velocity is 50 m/s. At the discharge end, the enthalpy is 2600 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. a. Find the velocity at the exit of the nozzle? b. If the inlet area is 900 cm? and specific volume at the inlet is 0.187 m/kg, find the mass flowrate? c. If the specific volume at the exit of the nozzle is 0.498 m/kg, find the exit area of nozzle? Fluid in + Fluid out V2 = ? V = 50 m/s A= 900 cm? hi = 2800 kJ/kg A2= ? h2 = 2600 kJ/kg
In a reaction stage of a stcam turbine the nozzle angle is 20° and the absolute velocity the steam at inlet to the moving blades is 240 m/s. The blade velocity is 210 m/s. If 1.7 the blading is designed for 50% reaction, determine: (i) the blade angle at inlet and exit; il the cathalpy drop per unit mass of steam in the moving blades and in the complete stage; (i) the diagram power for a steam flow of 1 kg/s: (iv) the diagram efficiency. (79.3, 20°; 25.3 kJ/kg; 50.6 kJ/kg; 50.6 kW; 93.5%)
Q5: A converging-diverging nozzle, which is shown in the figure, is supplied with air from a large tank where the pressure is Po and exhausts to the atmosphere with a pressure of Po. The area A at distance x from the throat is given by (A = At (1 + 0.75x/L)), where At is the throat cross- sectional area and Lis the total length of the diverging part of the nozzle. At a certain pressure ratio PoPb, a normal shock wave stands in the nozzle at a point where the Mach number before the shock is 1.7. Find the position of the normal shock wave from the throat, and the pressure ratio P/Po. Ans.: 0.45 L = 0.753 Р. Ps
A supply tank at 500 kPa and 400 K feeds air to a converging–diverging nozzle whose throat area is 9 cm2. The exit areais 46 cm2. State the conditions in the nozzle if the pressureoutside the exit plane is (a) 400 kPa, (b) 120 kPa, and (c) 9kPa. (d ) In each of these cases, fi nd the mass fl ow.
At atmospheric pressure of 100 kpa exists inside a room. Air is exhausted through a 0.5m diameter pipe into the atmosphere. The capacity of the fan is 2000m³/h, consuming a power of 1100 W at a speed of 1000rpm. There is a 60pa pressure drop in the suction while 0.80 kpa at the discharge side. Calculate the fan capacity if the operating speed is changed to 1200rpm with respective chance in power