Six steel cables are supporting a circular heavy moulding of diameter 2 m from an overhead point as shown in Figure MEC - 082. The moulding weighs 15.71 kN, and the attachment point is 3 m above it. Each cable is 10 mm in diameter and E = 42 GPa. 3 m 2 m Figure MEC - 082 Find the vertical movement of the moulding. Select one: O a. 0.0044 mm O b. 0.0032 mm O c. 0.0027 mm O d. 0.0055 mm

Six steel cables are supporting a circular heavy moulding of diameter 2 m from an overhead point as shown in Figure MEC - 082. The moulding weighs 15.71 kN, and the attachment point is 3 m above it. Each cable is 10 mm in diameter and E = 42 GPa. 3 m 2 m Figure MEC - 082 Find the vertical movement of the moulding. Select one: O a. 0.0044 mm O b. 0.0032 mm O c. 0.0027 mm O d. 0.0055 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The plate ACDE Axed as vertical as shown in Fig H,G, EIA Ball and Socket (255) The mo ment 9o EN-m about the line DL in x2-plane, EH Coincided over the x-axis, Determine the tension. in Cable and all reactions in ball ad Socket A- 2m krcable 2m 4 m parrallel fo 2 small 20 KN 5m JE neglected weight 6 m frictionless 30 90KNM Fig.Q#1
Part A: Two bolts secure a plate to a girder as shown in Figure a below. A 3kN vertical load is applied. a) Replace the applied load at C with a force-couple at D. (b) Assuming the bolts carry equal amounts of shear and applied moment, calculate the resultant bolt load due to the applied force-couple. Draw a FBD of the bolt group with the applied force-couple and bolt reacts. 350mm A 300mm 3kN
The bracket BCD is hinged at € and attached to a control cable | ! at B. For the loading shown, determine (a) the tension in the cable, (b) the reaction at C. a=0. 18m 20N 20N 8 c o I_.l_nm—l—um—-l 02¢m
EN O Aロa。 USEFUL LINKS v M Time Select the reinforcing needed for the short tied column shown for the following: Pn=2000 kN, 250 mm, e 200 mm. f28 MPa, fy= 420 MPa: (Add attachments below) 70 s00 mm 640mm 70 mm 70 mm 70 mm 210 mm 350 mm
2. The crank mechanism shown below is in equilibrium. Determine: a) the diameter of cylindrical connecting rod CD, given that normal stress is limited to 120MPa; b) the shear stress in the pin at B, where the pin has diameter of 8mm; and c) the bearing stress in the bracket supports at B. C 120° A 8kN 300mm B 30⁰ D P 200mm 6mm B 15mm 6mm 8mm Detail of pin and pin brackets
The connection consists of a plate connected to another plate by five 25-mm diameter rivets. It carries a load P = 80 kN. %3D Determine the shear stress on the bolt due to the effect of force alone? Determine the maximum shear stress on the bolt due to the effect of moment alone? Determine the maximum shear stress on the bolt? 80kN 200mm 80mm 80mm 120mm
2. Determine the adequacy of the clip angle connection shown. The allowable stresses are 100 MPa for shearing, 220 MPa for bearing, and 140 MPa for tension for the seat angle and the rivets. 45 kN 220 mm I 16 65 32 150 150x100x16 clip angle 20 mm o rivets 16 100
Test#1 -zzen-zax AlpQLSdM75VMOVqbMa1WtS9n99RYc6PifeGUTpVBOluyMUUVYQgqqA/formResponse YouTube Replace the three forces which act on the bent bar by a force-couple system at *.the support point A 2100 lb 4' 1500 lb •A B. 30° C. 2' •E. 800 lb 3' oogle
Problem 12 A plate is fastened to a fixed member by four 16mmP rivets arranged as shown. Compute the maximum shearing stress developed in the rivets. 30KN 100mm spacing 30KN
tab Gate AB in Figure below is semi-circular, hinged at B, and held by a horizontal force F2, at point A. What horizontal force F2 is required at point A for equilibrium? A- Ta IT 3- 14.14 V caps %3D %3D 2. Y = Ya 43) -1,27 37T 31T 2.5m 55 Waker F2 alm 3 m Ixc= a"(9n²- 64) 3"(Ap?-64) 72TT = 8,89 Side view 72T1 heg= Oh-CG 5.5-1.27 = 4,23 10 IxC e = 8,89 F= 10.(9.8 1) -(4.23) · (14,14) = 586,757.69 heg A 4,23 (14.149 NY86 Am-cG-e 1,27-. 1496=1.12 = arm+ FR ,12+586,757,68 3. = 195586,26 N
SITUATION 1 An eccentrically loaded bolted connection is shown. Diameter of A 325 bolts in standard holes is 19mm. The applied load is 45kN a. Determine the polar moment of Inertia of the group bolts b. Determine the torsional force on the critical bolt c. Determine the shearing stress of critical bolt. Le = 250 mmP = 45 kN 100 100 '15 75
2. A staggered riveted connection has rivets arranged as shown. Diameter of rivet is 28 mm. Use AISCINSCP Specs. Fy 248 MPa, Fu = 400 MPa. Determine the distance "S" so that the area area in chain ABCD is equal to the net area in chain ABD. Determine also the tensile capacity of P. 45 10 350 mm 90 90 I mm 60 mm 888