Shown is the stress-strain curve developed from the tension test of a metal alloy bar. The specimen used to develop the stress-strain curve has a round cross-section with a diameter of d = 7 mm and a gauge length of L = 370 mm. Determine the load that must be applied to the specimen to stress the specimen to it's 0.2% offset yield. Express your answer in kN to the nearest whole kN. Your written solution must also include the length of the specimen when stressed to the 0.2% offset yield stress. σ (MPa) 700 600 500 400 300 200 100 0 0.02 0.04 0.06 0.08 0.10 0.002 0.004 0.006 0.008 0.010 € (mm/mm) P d

Shown is the stress-strain curve developed from the tension test of a metal alloy bar. The specimen used to develop the stress-strain curve has a round cross-section with a diameter of d = 7 mm and a gauge length of L = 370 mm. Determine the load that must be applied to the specimen to stress the specimen to it's 0.2% offset yield. Express your answer in kN to the nearest whole kN. Your written solution must also include the length of the specimen when stressed to the 0.2% offset yield stress. σ (MPa) 700 600 500 400 300 200 100 0 0.02 0.04 0.06 0.08 0.10 0.002 0.004 0.006 0.008 0.010 € (mm/mm) P d

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the fracture 2.00 in. The data is listed in the table. Plot the stress-strain 8-1. A tension test was performed on a steel specimen n original diameter of 0.503 in. and gage length of PROBLEMS *84. origi the f having an for t and stress. Use a scale of 1 in. Dodraw the elastic region, using the same stress scale but a 20 ksi and 1 in. = 0.05 in./in. strain scale of 1 in.= 0.001 in./in. Load (kip) Elongation (in.) 0. 0. 0.0005 0.0015 1.50 4.60 8.00 11.00 0.0025 0.0035 0.0050 11.80 11.80 0.0080 0.0200 12.00 16.60 0.0400 0.1000 0.2800 20.00 21.50 19.50 18.50 0.4000 0.4600 Prob. 8-1
Determine the resulting maximum value of the normal stress. Specify the orientation of the plane on which these maximum values occur. **The answer is tensile stress is 0 ksi at 90 degrees. **The answer is compressive stress is 7 ksi at 0 degrees. Can you explain how that is? This was my thought process: I know that tensile would be zero because the force P is actually going inwards and not outwards. I know that means that there would be a compressive force. I am confused on the angles, how is a tensile force going 90 degress if there technically is no force in the tensile direction. And how is there a compressive force at 90 degrees if there is a stress? thank you!
You are in charge of designing a new fixture for a “universal testing machine” that will attach a tensile specimen to the machine using a clevis—a U-shaped piece with holes drilled through the two arms—and a cylindrical pin that passes through the clevis and the specimen. If the maximum load exerted by the machine is 30 kN and the pin is to be made of some sort of steel, what is the minimum pin diameter needed to ensure that the shear stress in the pin does not exceed 600 MPa? Assume that the steel has similar elastic properties to pure Fe.
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 8 (Example: 12Q°C = 120°C). Just substitute the number in letter. Thank you! Determine the normal stress and change in length of the aluminum rod if the temperature was raised by 12Q°C. The 0.5-mm gap exists at 2T°C.
Q2 A tensile test specimen having a diameter of (10 mm) und a page length of (S0 mm) was tested to fracture The stieisitrain curve from the tensiotn test is shown in Figure (9) The lower plat is the expanded tegion OAT and associatod with the strain valuns tiven on the lower scale Determine, 480 Lpper veile AB 241 Loser scale + The ultimaie stress, be The propotional limit, 120 e The fracture strees 4 The modulus of elasticity, OAK 0.04 0.0s 0.00 0.12 0.16 1.20 0K2 DANN 0.006 0.008 0.010 e T'he offiet yield stuen at 0.2%, Strain tmm/um) G The asial force ucting on the specireni whert t i uxtended by Figuie (3) a sans
Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain = 0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in the y-direction, the width strain was measured to be gw=-0.1000 at that instant. The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi. Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be expected.
An engine parts is being tested with a load of 60000 lb. The allowable tensile stress is 10000 psi, modulus of elasticity of 40x106 psi. If the original length of specimen is 42 inches with elongation not exceeding 0.0015 in, what diameter of the specimen is rejected? a. 4.2 in b. 3.0 in c. 2.5 in d. 5.17 in
The state of plane stress shown occurs at a critical point of a metal machine component. As a result of several tensile tests, it has been found that the tensile yield strength is Fy for the grade of metal used. Determine the ratio of OT/ OH shown in the figure, using the maximum-shearing-stress criterion (Tresca Hexagon). (Using Mohr circle method to calculate principle and average stresses) OX TXy Mpa Mpa Mpa MPa ob σy тху 90 -60 45 310 dy OX x Sx=Sx Sy=sy txy=txy Fy=Yield Strength Answer
1. We can visualize the factor of safety for an arbitrary stress using a surface in principal stress space. For a ductile material that yields according to a von Mises criterion with a yield stress σy, sketch the von Mises surface in σ₁ - 02 space and sketch the stress surface that corresponds to a factor of safety FoS = 2. For a brittle material that yields according to a max normal (Rankine) criterion with a tensile strength Gyt and a compressive strength σvc = 20yt, sketch the yield surface and the surface that corresponds to a factor of safety FoS = 2.
gure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30kN. If Young's odulus for the alloy is 69GPA determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3 P Figure 1
Electrical strain gauges were applied to a notched specimen to determine the stresses in the notch. The results were ex = 0.0019 and ey = -0.00072. Find ox and ay if the material is carbon steel.
A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. The data is listed in the table. Plot the stress–strain diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the rupture stress. Use a scale of 25 mm = 140 MPa and 25 mm = 0.05 mm/mm. Redraw the elastic region, using the same stress scale but a strain scale of 25 mm = 0.001 mm/mm.