Several buildings have foundations made of material such as concrete. In fact, the compressive strength of concrete is a critical factor in providing a firm foundation of structures. The stress-strain diagram of concrete shown below has the points of failure as indicated by dots. (a)Determine the Young's modulus for this particular concrete under compression. See stress-strain diagram in figure 05. *

Several buildings have foundations made of material such as concrete. In fact, the compressive strength of concrete is a critical factor in providing a firm foundation of structures. The stress-strain diagram of concrete shown below has the points of failure as indicated by dots. (a)Determine the Young's modulus for this particular concrete under compression. See stress-strain diagram in figure 05. *

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using Figure 4, a cross-section of a concrete beam, answer the questions that follow.5.1. Calculate the moment of inertia about the X-axis and the Y-axis 5.2 Calculate the combined bending and direct stress at points A, B and C. All loading is assumed to compressive. revision paper 2020
A concrete specimen with b = d is supported at both ends 600mm apart. It is tested for flexure strength with load at midspan of 100kN and failed with a flexural stress of 52.083 MPa. What is the dimension b and d of the specimen in mm?
4.1 Consider the prestressed concrete beam and prestressing steel stress-strain diagram given below. The concrete is assumed to have an ultimate strain capacity of 0.003 in/in. Determine the nominal strength of the member using the strain compatibility method. It should be noted that the stress-strain diagram below allows virtually "exact" calculation of stresses and strains in the prestressing steel. Assume that the specified concrete strength is 4,000 psi, fse = 137 ksi, Ec = 3850 ksi, Ecu = 0.003, p = 0.40 and Eps = 28,000 ksi. 20" 4" 3" -10" O -10" (a) 17.58" Ap = 0.575 in.2 fp ksi 250 213 0.0079 Ep (b) 0.067
1.Why is the compression test the one most frequently made for concrete? 2.Discuss why cross-sectional area of compression specimens must be larger than those of tension specimens. 3.Can you think of any instances where materials are intended to fail in compression
what would be the average compressive strength of concrete if the load at failure of the 3 trials are 55,100 kg 54,800 kg and 55,200 kg. Diameter of the sample is 6" a. 31.1 MPa b. 30.6 MPa c. 31.6 MPa d. 30.1 MPa
A cylindrical block of concrete is 300mm long and has a circular cross section of 100mm in diameter. It carries a total compressive load of 67KN and under this load contract 0.2mm. Estimate the compressive stress and strain .
Problem 1: A square concrete column with dimensions 22 x 22 in. is reinforced with a total of eight No. 10 bars arranged uniformly around the column perimeter. Material stress-strain are given by curves a and c in Fig 1. Calculate the percentages of total load carried by the concrete and the steel as load is gradually increased from 0 to failure, which is assumed to occur when the concrete strain reaches a limit value of 0.0030. Determine the load at strain increments of 0.0005 up to the failure strain, and graph your results, plotting load percentage vs. strain. (Source: Design of Concrete Structures 16th ed., McGraw-Hill, 2021) (Hint: use strain compatibility) fs, ksi 60- 50 40 30 20 10 OL fc, ksi 6 5 T 4 3 2 1 0 0.001 Es or Ec Fig. 1 b a Steel b Concrete, fast loading c Concrete, slow loading d Elastic concrete 0.002 0.003
4. The state of two dimensional stress acting on a concrete lamina consists of a direct tensile stress of 6 MPa and shear stress of 4 MPa, which cause cracking of concrete. Then what will be the tensile strength of the concrete in MPa.?
Two 150 mm * 300 mm concrete cylinders with randomly oriented steelfiber contents of 0 and 2% by weight, respectively. After curing for 28 days,the specimens were subjected to increments of compressive loads until failure. The load versus deformation results were as shown in Table P7.45. Assuming that the gauge length is the whole specimen height, determine the following:a. The compressive stresses and strains for each specimen at each loadincrement.b. Plot stresses versus strains for the two specimens on one graph.c. The initial modulus of elasticity for each specimen.d. The ultimate strength for each specimen.e. The strain at failure for each specimen.f. Toughness. Curves may be approximated with a series of straight lines.g. Comment on the effect of adding fiber on the following:i. Modulus of elasticityii. Ultimate strengthiii. Ductilityiv. Toughness
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. if the tensile strain is set as 0.009 upon crushing of concrete at a strain of 0.003. = [rr] (5 decimal places)
Strain profiles of a flexural reinforced concrete element section at yield and failure conditions are given in Figure 1. (a) Does this section satisfy the curvature ductility requirement of µ> 8. (b) Briefly indicate two possible design modifications by which the ductility of a reinforced concrete section can be improved. &= 0.002 Eu = 0.004 fy = 460 MPa Es = 200 GPa d Ey Es = 10ɛy Yield Failure Figure 1: Strain Profiles
A 150mm diameter cylindrical concrete specimen was tested for compressive strength. What would be the maximum applied force in kN when the stress at failure is 41.4 MPa?