set to R = 26.02. The switch S in the circuit now is closed. To what resistance must the variable resistor be set if bulb #1 is to have the same brightness after the switch is closed as it did with the switch open?

set to R = 26.02. The switch S in the circuit now is closed. To what resistance must the variable resistor be set if bulb #1 is to have the same brightness after the switch is closed as it did with the switch open?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The diagram below shows a small water heater that uses electrical energy to heat water. The heating element is a small resistor labeled Rjoad = 5.0 N immersed in the water. A 20 V ideal emf device supplies current and there is an adjustable resistor Ra in series. The value of the adjustable resistance can be changed to be anywhere between 1.0 - 3.0 N. The adjustable resistor is initially set to 2.0 N and the switch is closed. (a) What is the voltage drop across the heating element? (b) How much energy is supplied by the source if the water heater runs for 10 minutes? (c) What fraction of this energy is actually used to heat the water? Please express your answer as a percentage, using only two significant figures. (d) Suppose the heating element degrades and corrodes and its resistivity slowly increases as the equip- ment becomes older. • Does the voltage drop across the heating element increase, decrease or remain the same as the equipment gets older? • Does the the total power…
The capacitor, C1 = 1.2 pF, in the circuit below begins with no stored charge. At t = 0 seconds, the switch is closed. What is the current (in mA) through the resistor, R1 = 9.1 MQ, at t = 4.2 usec? R1 +12V ww
The capacitor shown below has an initial voltage of 0.15 V before the switch is closed. The resistance is 8.5 x 106 ohms and the capacitance is 2.0 microfarads. How long after the switch is closed in seconds does it take for the voltage across the resistor to drop to 0.083 V? R CH B A D
The part with the switch and two resistors R1 in parallel of the circuit below dissipates the same amount of power whether or not the switch is closed. Neglecting any internal resistance in the battery, determine the value of R1 in terms of R.
In the circuit shown in the following figure(Figure 1) the capacitor has capacitance 18 μFμF and is initially uncharged. The resistor R0R0 has resistance 12 ΩΩ . An emf of 80.0 VV is added in series with the capacitor and the resistor. The emf is placed between the capacitor and the switch, with the positive terminal of the emf adjacent to the capacitor. The small circuit is not connected in any way to the large one. The wire of the small circuit has a resistance of 1.1 Ω/mΩ/m and contains 30 loops. The large circuit is a rectangle 2.0 mm by 4.0 mm, while the small one has dimensions aaa = 10.0 cmcm and bbb = 19.0 cmcm . The distance cc is 4.0 cmcm . (The figure is not drawn to scale.) Both circuits are held stationary. Assume that only the wire nearest the small circuit produces an appreciable magnetic field through it. The switch is closed at tt = 0. When the current in the large circuit is 5.00 AA , what is the magnitude of the induced current in the small circuit?
Switch S in in the figure is closed at time t = 0, to begin charging an initially uncharged capacitor of capacitance C = 17.2 μF through a resistor of resistance R = 21.2 Ω. At what time is the potential across the capacitor equal to that across the resistor?
In the circuit below each capacitor initially has a charge of magnitude 3.50 nC on its plates. After the switch S is closed, what will be the current in the circuit at the instant that the capacitors have lost 80.0% of their initial stored energy?
R1 S R3. R2 4. Determine in the current in each resistor given that R1 = R2 = R3 = 12, the capacitance C = 0.5 µF, and potential across the batter of E = 2V when the switch is closed at t = 0. Determine then after some time (t = x) after the switch is closed the currents in each resistor.
The circuit on the right contains three resistors, A, B, and C, which all have equal resistances. The emf is 110V. Which resistor dissipates the most thermal energy after the switch is closed? (Resistor A, B, or C). Why? What other quantity is maximized to tell you that the energy is maximized?
5.0 k2 and R2 =10.0 k2, along 4. In the circuit shown, there are two resistors, with R1 with a capacitor, with C=15.0 µF, initially uncharged, parallel to the second resistor. The battery supplies a voltage of &=30.0 V. The switch is closed at t= 0. (a) At that instant, what is the current in each resistor? What are the final (b) currents and (c) charge on the capcitor when the switch has been closed for a long time? (d) When the switch is re-opened, what is the time-constant for the discharging capacitor? R C
When switch S in (Figure 1) is open, the voltmeter V of the battery reads 3.13 V. When the switch is closed, the voltmeter reading drops to 2.93 V, and the ammeter A reads 1.69 A. Assume that the two meters are ideal, so they don't affect the circuit. For related problemsolving tips and strategies, you may want to view a Video Tutor Solution of A source with a short circuit. Figure S V r E -ww+ R A 1 of 1 Find the emf. Express your answer in volts. E = Submit Part B r = Find the internal resistance r of the battery. Express your answer in ohms. Submit Part C Π| ΑΣΦ Request Answer R= | ΑΣΦ Request Answer Find the resis ance R. Express your answer in ohms. IVE| ΑΣΦ ? ? ? V Ω Ω
The figure below shows a capacitor, with capacitance C = 30.0 µF, and a resistor, with resistance R = 45.0 ko, connected E= 19.0 V. The circuit has a switch, which is initially open. (a) What is the circuit's time constant (in s)? (b) After the switch is closed for one time constant, how much charge (in C) is on the capacitor?