"Select the most suitable complement among listed options for the 10 items: T) Real fluids (a) are viscous (b) possess surface tension (c) are compressible (d) possess all the above properties (e) possess none of the above properties. 2) In a static fluid (a) resistance to shear stress is small (b) fluid pressure is zero (c) linear deformation is small (e) viscosity is nil. (d) only normal stresses can exist 3) When the flow parameters at any given instant remain same at every point, then flow is said to be (d) uniform (e) Static. (a) Turbulent (b) Steady state (c) laminar 4) The increase of temperature results in (a) increase in viscosity of gas (b) increase in viscosity of liquid (c)decrease in viscosity of ga (d) decrease in viscosity of liquid (e) (a) and (d) above. 5) Consider the flow in pipe in figure. If P₁ -AP/y. b) The ow direction is from 2 to 1 if AZ <-AP/y. c) T flow is zero if AZ = -AP/y. d) The flow is zero if AZ = AP/y. Q 6) Air flow though the device shown in figure. Select which set of the following conditions is TRUE assuming incompressible non-viscous steady flow ½-1 2 (a) p4 v3 (b) p3> pl; vl > v3 (c) p2 p3; v2> v3 (d) p4 vl (e) p4> pl; v4

"Select the most suitable complement among listed options for the 10 items: T) Real fluids (a) are viscous (b) possess surface tension (c) are compressible (d) possess all the above properties (e) possess none of the above properties. 2) In a static fluid (a) resistance to shear stress is small (b) fluid pressure is zero (c) linear deformation is small (e) viscosity is nil. (d) only normal stresses can exist 3) When the flow parameters at any given instant remain same at every point, then flow is said to be (d) uniform (e) Static. (a) Turbulent (b) Steady state (c) laminar 4) The increase of temperature results in (a) increase in viscosity of gas (b) increase in viscosity of liquid (c)decrease in viscosity of ga (d) decrease in viscosity of liquid (e) (a) and (d) above. 5) Consider the flow in pipe in figure. If P₁ -AP/y. b) The ow direction is from 2 to 1 if AZ <-AP/y. c) T flow is zero if AZ = -AP/y. d) The flow is zero if AZ = AP/y. Q 6) Air flow though the device shown in figure. Select which set of the following conditions is TRUE assuming incompressible non-viscous steady flow ½-1 2 (a) p4 v3 (b) p3> pl; vl > v3 (c) p2 p3; v2> v3 (d) p4 vl (e) p4> pl; v4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Surface tension is due to uneven molecular attraction between immiscible fluid media and solid surface. Its importance is governed by dimensionless parameter Which of the Inertia force called Weber number given by We = Surface tension force™ following statements are correct? (i) Surface tension becomes important when the length scale L is small such as in ink jet printing, coating of thin film, oxygenation of water by falling rain drops. (ii) 111 Super-hydrophobicity can be achieved by micro/nano texturing of surface such as in lotus leave, butterfly and dragonfly wing. During oil spill in ocean, oil floats and spreads out due to gravity. By conservation of mass, the oil film becomes thinner as it spreads. Finally, the surface tension force becomes important causing the formation of tiny oil droplets. (A) (B) (C) (D) (i) and (ii) (i) and (iii) (ii) and (iii) All of the above
Assignment 3 On Viscosity Calculation - Word TOUT REFERENCES MAILINGS REVIEW VIEW Hyperlink P Bookmark tArt Chart Screenshot Apps for Office Online Video Cross-reference Comment Header Footer Page Number Text Quick WordA Box Parts - ns Apps Media Links Comments Header & Footer (2) Referring to the following figure, the distance between plates is Ay = 0.5 cm, Av: = 10 cm/s, and the fluid is ethanol at 273 K having a viscosity of 1.77cp (0.0177 g/cm s). (a) Calculate the shear stress ty and the velocity (b) gradient of shear rate -/dy using cgs units. (c) Repeat using SI units. A Torce Fdshear berween teoparailel plates
Q2) Fill in the blanks with appropriate word(s), for EXKEl of the following; K Specific weight is defined as According to the variation of density with pressure, Nuids may be classified into - Nuids and - Nuids. 3. The approximate number of experiments to evaluate the influence of 3 parameters separately is assuming that 5 experiments are needed for each variable. ¿When viscous resistance is important, -. criteria for similarity is used. S. The center of pressure is defined as - A Hydrostatic forces in a static fluid is the result of the exerted on submerged surfaces. Streamline is defined as Continuity equation represents the d 0, conservation of
In the following section, at least 2 to up to 5 answers may be correct. 1) For a fluid, the assumption (simplifying notion) of incompressibility has important consequences: Pascal’s principle: a change of pressure in an enclosed fluid at rest is transmitted undiminished to all points in the fluid. pressure changes are transmitted immediately from one place to another. the speed of sound then is infinite (just within this approximation). pressure becomes unpredictable. none of the above. 2) Archimedes’ principle can be summarized as: an immersed object is buoyed up by a force equal to the weight of the fluid it displaces. a bathtub is fun, and may lead to important physical discoveries regarding the volume of an object and how much water it displaces, and the weight of that amount of water. boats swim because of the work done by sailors. submarines are always doomed. fish swim because they are less heavy than water 3) A…
You have been moved into the laboratory for the fluid testing for hydraulic devices, where your job is to illustrate the results of a viscosity test on a Newtonian fluid at various temperatures and explain discrepancies after completing the following given data-sheet in Table A. A considerable amount of research has been carried out in an attempt to understand the exact nature of the temperature variation of viscosity. One relatively simple model assumes that the viscosity obeys an 'Arrhenius-like' equation of the form n = Xe(k)r Хе --------Equation 1 where X = 1.7419 and (E/R) = -0.018 are constants for a given fluid. You are required to carry out appropriate calculations on the effect of changes in temperature given in table A by using equation 1 for Ethanol on the viscosity of a fluid. Table A NO Temperature viscocity n T°C cP 10 3 20 30 40 6. 50 7 60 8. 70 2. 4) 5.
We consider a bar rotating, with friction due to viscosity, around a point where a torque is applied. The non-linear dynamic equation of the system is given by ml²ö = -mgl sin 0 – kl²ė + C where 8 - is the angle between the bar and the vertical axis; C- is the torque (C>0); k – is a viscous friction constant; l- is the length of the bar; m – is the mass of the bar; a) Choose appropriate state variables and write down the state equations; b) Find all equilibria of the system, assuming that < 1; c) Linearize the system around equilibrium points and determine the eigenvalues for each equlibria; mgl
Select two saturated and two unsaturated samples of air from the dataset of pressure and temperature given below: Pressure (mb): 10, 20, 30 Temperature (°C): 10, 20, 30 Let A and B be two air samples, where A: (T=30°C, P=25 mb) and B: (T=30°C, P=30 mb). For each sample, determine the following: a. Saturation vapor pressure b. Dew point c. Relative humidity d. If samples A and B were cooled to 15°C. What would be their relative humidity? What would be their dew point temperature?
The heat flux for stable film boiling on the outside of a horizontal cylinder or sphere of diameter D, in m, is given below. What should be the value of "n", for the equation above to be dimensionally consistent? Use dimensional analysis: q=heat flux, W m² W k = thermal conductivity of vapor, 'm °C hgf - [g kỷ Pv(P₁ − Pv)[hfg + 0.4 Cpv (Ts − Tsat)]] à = Cf MyD (Ts - Tsat) Pv = density of vapor, P₁ = density of liquid,- kg m³ kg 'm³ Cpv = enthalpy of vaporization, kg g = gravitatioinal acceleration, C = experimental constant, dimensionless m J kg °C Ts = surface temperature of the heater, °C Tsat = saturation temperature of vapor, °C kg Hv = viscosity of vapor, ms = specific hear of vapor, (Ts - Tsat)
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.
01) Select the most suitable complement among listed options for the 10 items: 1) Real fluids are compressible (a) are viscous (b) possess surface tension (c) (d) possess all the above properties (e) possess none of the above properties.
Fluid Mechanics - Dimensional Analysis
Q1: Apply appropriate solution method using math principles to prove that "the pressure at a point in a fluid has the same magnitude in all directions". Support your answer with sketch. Answer: Px Pz = Pn P are the mean pressures at the three surfaces in the x- and z-directions. Q2: Formulate the issue and identify key variables to prove that [AP = P2 - P, = pg Az = y, Az], where y, and p are the specific weight and density of the fluid, respectively. Az is the vertical distance. Support your answer with sketch. Q3: From fluid mechanics science perspective, define the center of gravity and the center of pressure. Q4: Identify the hydrostatic force acting on the top surface of a submerged rectangular plate by applying principles of engineering for the following cases: 1 tilted plate, (2 vertical plate, and 3 horizontal plate. Support your answer with sketch. Q5: By applying principles of fluid mechanics science, define the "rigid-body" and identify its features. Q6: Formulate the issue…