Solve correctly need urgently Saturated liquid water is heated in a heat exchanger until it exits as a saturated liguid vapor mixture. Hot oil is used to heat the water. The hot oil enters the heatexchanger at 150 C and exits at 40 C. The mass flowrate of the hot oil is 10 kg/s and has a specific heat of 2.2 kJ/kg-C. The water enters the heat exchanger at 25C and 100 kPa. The water leaves the heat exchanger as a saturated liquid vapor mixture at 100 kPa. The mass flowrate of the water is 1.5 kg/s. It is also knowthat the enthalpy of the water exiting the heat exchanger is 1718.2 kJ/kgIn the question that follows, select the answer that is closest to the true valueWhat is the quality of the water at the exit of the heat exchanger?O 0576O 0 933O 0 862O 0 791

Answered: Image /qna-images/answer/682b2aa9-38b5-49a5-b5bc-830439331c4a.jpg

Answered: Saturated liquid water is heated in a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Saturated liquid water is heated in a heat exchanger until it exits as a saturated liquid vapor mixture. Hot oil is used to heat the water. The hot oil enters the heat exchanger at 150 C and exits at 40 C. The mass flowrate of the hot oil is 11 kg/s and has a specific heat of 2.2 kJ/kg-C. The water enters the heat exchanger at 25 C and 100 kPa. The water leaves the heat exchanger as a saturated liquid vapor mixture at 100 kPa. The mass flowrate of the water is 1.5 kg/s. What is the enthalpy of the water at the exit of the heat exchanger in units of kJ/kg? Select the answer that is closest to the true value. A) 911 B) 1234 C) 1557 D) 1879 A Moving to another question will save this response. Question 1 of 11
Steam at 1.6 MPa and 350°C enters a steam turbine at a flow rate of 16 kg/s. Thesteam leaves the turbine as a saturated vapor at 30°C. The turbine delivers 9 MW ofpower. A schematic of the turbine and its operating conditions are given in theFigure below. Determine the heat transfer rate from this turbine.
Saturated liquid water is heated in a heat exchanger until it exits as a saturated liquid vapor mixture. Hot oil is used to heat the water. The hot oil enters the heat exchanger at 150 C and exits at 40 C. The mass flowrate of the hot oil is 5 kg/s and has a specific heat of 2.2 kJ/kg-C. The water enters the heat exchanger at 25 C and 100 kPa. The water leaves the heat exchanger as a saturated liquid vapor mixture at 100 kPa. The mass flowrate of the water is 1.5 kg/s. In the question that follows, select the answer that is closest to the true value. What is the enthalpy of the water at the exit of the heat exchanger in units of kJ/kg?
Ammonia and air pass through the heat exchanger. While the ammonia is entering as a superheated vapor at 16 bar pressure and 60C temperature it is leaving as a saturated liquid at the same pressure but unknown temperature. The ammonia mass flow rate is 400 kg/hour. Air is flowing backward and is heated from 17C to 42C at the constant pressure of 2 bars. NOTE: Find air properties from https://www.peacesoftware.de/einigewerte/luft_e.html a.Draw the sketch of the heat exchanger showing all thermodynamic parameters (P, T, etc.) Please show all steps of solution
A fruit juice is being heated in an indirect heat exchanger using steam as a heating medium. The product fl ows through the heat exchanger at a rate of 1500 kg/h and the inlet temperature is 20C. Determine the quantity of steam required to heat the product to 100C when only latent heat of vaporization (2200 kJ/kg) is used for heating. The specifi c heat of the product is 4 kJ/(kg C).
Steam at 200 kPa and 150°C is used to prepare hot water in a flow system. The steam cools and condenses such that the outlet flow is a saturated liquid (note that flows in heat exchangers generally have negligible pressure differences between the inlet and outlet.) The water to be heated enters at 10°C and we want 55°C (~130°F) hot water at the outlet. If we want 0.1 kg/s of hot water, how much steam is needed (kg/s)? Steam 200 kPa 150°C Water 100 kPa 10°C 0.1 kg/s JL Water 100 kPa 55°C Saturated Liquid Condensate 200 kPa
Thermodynamics Refrigerant R-134a to the compressor of a refrigeration machine It enters at 140 kPa pressure and -10 °C, and exits at 1 MPa pressure. Volumetric flow of the refrigerant entering the compressor It is 0.23 m³/minute. The refrigerant enters the throttling valve at a pressure of 0.95 MPa and at 30 °C, and exits the evaporator as saturated steam at -18 °C. Adiabatic efficiency of the compressor It is 78%. Show the cycle in the T-s diagram. And; a) Calculate the power required to run the compressor. b) Calculate the heat absorbed per unit time from the cooled medium. ( COPSM=? ) c) Calculate, between the evaporator and the compressor, how much the pressure of the refrigerant drops and how much the heat gain.
Saturated propane vapor at 2:00 x 102 psia is fed to a well-insulated heat exchanger at a rate of 3:00 x 103 SCFH (standard cubic feet per hour). The propane leaves the exchanger as a saturated liquid (i.e., a liquid at its boiling point) at the same pressure. Cooling water enters the exchanger at70°F, flowing cocurrently (in the same direction) with the propane. The temperature difference between the outlet streams (liquid propane and water) is 15°F.(a) What is the outlet temperature of the water stream? (Use the Antoine equation.) Is the outlet water temperature less than or greater than the outlet propane temperature? Briefly explain.(b) Estimate the rate (Btu/h) at which heat must be transferred from the propane to the water in the heat exchanger and the required flow rate (lbm/h) of the water. (You will need to write two separate energy balances.) Assume the heat capacity of liquid water is constant at 1.00 Btu/(lb m°F) and neglect heat losses to the outside and the effects of…
a power plant steam, steam is continuously extractedfromthe turbine and in a heat exchanger there is a condensation of the extracted steam. The energy released during condensation of steam is used to operate a heat engine. A heat engine receives thermal energy at a rate of 1200 kJ/hr from condensing steam and rejects waste heat to a lake at 20°C at a rate of 800 kJ/hr. Determine the lowest possible condensing steam temperature.
Steam enters a steady-flow turbine with a mass flow rate of 20 kg/s at 600 C (Celsius), 5 MPa, and a negligible velocity. The steam expands in the turbine to a saturated vapor at 500 kPa where 10 percent of the steam is removed for some other use. The remainder of the steam is reheated to 600 C (Celsius in the reheater and then expands to the turbine exit where the pressure is 10 kPa and specific volume is 12.47 m3/kg. If the turbine is adiabatic, determine the ratio of the rate of heat added in the reheater to the rate of work done by the steam during this process. Select one: a. 0.99 b. 0.1 c. 1.5 d. 0.38
Steam enters a steady-flow turbine with a mass flow rate of 20 kg/s at 600 C (Celsius), 5 MPa, and a negligible velocity. The steam expands in the turbine to a saturated vapor at 500 kPa where 10 percent of the steam is removed for some other use. The remainder of the steam is reheated to 600 C (Celsius in the reheater and then expands to the turbine exit where the pressure is 10 kPa and specific volume is 12.47 m3/kg. If the turbine is adiabatic, determine the ratio of the rate of heat added in the reheater to the rate of work done by the steam during this process.
to 1 MPa and 30°C in a condenser by air. The air enters at 5-81 Refrigerant-134a at 1 MPa and 90°C is to be cooled and leaves at 95 kPa and 60°C. Determine the mass flow rate 100 kPa and 27°C with a volume flow rate of 600 m’/min of the refrigerant. Answer: 100 kg/min Air V3 = 600 m³/min P3 = 100 kPa| T3 = 27°C %3D %3D R-134a bole P1 = 1 MPa T = 90°C P4 = 95 kPa T4 = 60°C P2 = 1 MPa T2 = 30°C %3D FIGURE P5-81 window air

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS