Results of two consolidated-drained triaxial tests on a clayey soil are as follows: a's (kN/m?) Test no. (kN/m?) 1 104 320 2 207 517 16. Determine the angle of friction and cohesion in undrained condition 17. Determine the angle of friction and cohesion in drained condition if the porewater pressure is150 kPa

Results of two consolidated-drained triaxial tests on a clayey soil are as follows: a's (kN/m?) Test no. (kN/m?) 1 104 320 2 207 517 16. Determine the angle of friction and cohesion in undrained condition 17. Determine the angle of friction and cohesion in drained condition if the porewater pressure is150 kPa

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter12: Shear Strength Of Soil

Section: Chapter Questions

Problem 12.16P

See similar textbooks

Similar questions

9. A consolidated drained test was carried out on a sandy clay under a cell pressure of 250 kPa. A constant back pressure of 120 kPa applied throughout the test. The dimensions of the sample were 76 mm x 38 mm. Addional test data recorded at failure were: Load transducer force = 368 N 3 Measured change in volume = 2.42 x 10 m³ Axial deformation = 2.05 mm Determine the major principal stress, o, at failure. (455 kPa)
A sand sample in a triaxial test have the following stresses: Cell Pressure 25kpa 34kpa Axial Stress 33kpa 55kpa Pore Water pressure 12kpa 10kpa a. Compute the drained angle of internal friction. b. Determine the cohesion of the soil c. Find the angle of failure in shear
A cohesionless soil sample is subjected to a triaxial test. The critical state friction angle of the soil is 28 degrees and the normal effective at the failure is 200 kPa. Determine the critical state shear stress. Determine the plunger stress. Determine the cell pressure.
Question 2 The result presented in Table Q2a were obtained from a consolidated drained (CD) triaxial test on a normally consolidated clay sample of 75mm height x 38mm diameter tested at a confining pressure of 50 kPa. Table Q2a. CD triaxial test result Axial strain (%) 1 2 5 10 15 Applied force (kN) 0.01 0.03 0.05 0.08 0.10 Page 3 of 6 (a) Draw the Mohr circle for each stress state in the sample and the total stress path (TSP) throughout the test and determine the slope of the TSP to the horizontal.
A CU triaxial test was carried out on a silty clay that was isotopically consolidated using a cell pressure of 125 kPa. The following data were obtained: Axial load (kPa) 0 5.5 11.0 24.5 28.5 35.0 50.5 85.0 105.0 120.8 Axial strain, &₁ (%) 0 0.05 0.12 0.29 0.38 0.56 1.08 2.43 4.02 9.15 Au (kPa) 0 4.0 8.6 19.1 29.3 34.8 41.0 49.7 55.8 59.0 (a) Plot the deviatoric stress vs. axial strain and excess porewater pressure vs. axial strain, respectively. (b) Determine the undrained shear strength (sµ). (Note: we assume that the sample reaches failure). (c) Determine the total principal stresses (0₁,03) and the effective principal stresses (0₁, 03') at the failure, respectively.
A triaxial test is performed on a normally consolidated clay. The sample is further consolidated by the test of all-around confining pressure prior to application of the axial load. The axial force is then applied very slowly. The equipment pore pressure lines remain open so that drainage of soil pore water can occur during the test. (The described conditions outline the procedure for a consolidated–drained-type test.) The sample fails (shears) when the σ3 pressure is 21 kPa and the s1 value is 61 kPa. From these data, determine the angle of internal friction for the effective stress strength–failure envelope (that is, determine fCD).
The results of two consolidated-undrained triaxial tests on an over-consolidated clay soil are as follows: Test Number o1 U (all in kPa) 03 1 190 65 35 2 340 130 60 Determine the total (C/o) and effective (C'/o') strength parameters in kPa (C) and angle degrees ().
Below are results from three unconsolidated undrained triaxial tests performed on a fully saturated clay specimen: Test No. 1 2 Minor principal stress (psi) Major principal stress at failure (psi) 10 25 33 22 37 45 Moisture content = 21 % Determine: a) Void ratio (e) of the soil. You may use eS = wG_ (assume Gs = 2.70) %3D b) Deviatory stress at failure for each test trial c) Shear strength parameters (cu and ø). Hint: Sketch the Mohr's circles for the three trials. 3.
A normally consolidated soil was subjected to tri-axial test with the following data: cell pressure= 320kPa; The specimen failed when the deviator stress is 460 kPa. Compute the angle of resistance in degrees.
A consolidated-undrained tri-axial test was conducted on a normally conslidated clay sample and the results are follows: Chamber confining pressure= 119kpa Deviator Stress at failure=90 kpa Pore water pressure= 58kpa These results were used to determine the drained friction angle of the soil. Compute the deviator stress (kpa) at failure when the drained test was conducted with the chamber confining pressure changed to 156 kpa. Use stored value. Answer to 5 decimal places.
Sample of clay isotropically normally compressed to an all round effective pressure of 100 kPa and then allowed to swell back to an effective isotropic pressure of 50 kPa. The sample is then subjected to a standard drained compression test. What is the deviator stress at failure and what is the volumetric strain experienced by the sample at failure? The second sample is subjected to a standard undrained compression test. What are the deviator stress and pore pressure at failure, if there is initially back pressure of 50kPa? Assume that the soil has the following critical state properties: M = 0.95, λ = 0.093, K = 0.035, I = 2.06 and N= 2.118
For a normally consolidated soil, the following is given: Determine the following: a. The compression index, Cc. b. The void ratio corresponding to pressure of 200 kN/m2