! Required information A load impedance, Zo = 10 +j3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part Line ww VS(rms)=230/0°V Zo Load Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are 957 and 974, respectively.

! Required information A load impedance, Zo = 10 +j3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part Line ww VS(rms)=230/0°V Zo Load Determine the average powers delivered to the load and absorbed by the line. The average powers delivered to the load and absorbed by the line are 957 and 974, respectively.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.3P: The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Calculate the impedance ?? for the maximum average power transfer in the circuit shown in Figure 3.and ??Find the value of the maximum average power transferred to?
The steady-state voltage drop between the load and the sending end of the line seen in (Figure 1) is excessive Suppose that V-4950/0° V (rms). A capacitor is placed in parallel with the 192 kVA load and is adjusted until the steady-state voltage at the sending end of the line has the same magnitude as the voltage at the load end, that is, 4950 V (rms). The 192 kVA load is operating at a power factor of 0.8 lag. Part A Calculate the size of the capacitor in microfarads if the circuit is operating at 60 Hz. In selecting the capacitance, use the value that results in the lowest possible power loss in the line. Express your answer in microfarads to three significant figures. ▸ View Available Hint(s) Figure 1 of 1 202 1100 192 kVA 0.8 lag ΜΕ ΑΣΦ. 11 vec C= 22.8 Submit Previous Answers Incorrect; Try Again; 5 attempts remaining Provide Feedback ? F
A surge of 100 kV travels along an overhead line towards its junction with a cable. The surge impedance for the overhead line and cable are 400 ohms and 50 ohms respectively. The magnitude of the surge transmitted through the cable is ?
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
128, An equipment has an impedance 0.9 p.u. to a base of 20 MVA, 33 kV. To the base of 50 MVA, 11 kV, the p.u. impedance will be (a) 4.7 (c) 0.9 (b) 20.25 (d) 6.75
5.5 kW, 1450 rpm. L-type equivalent circuit and parameters for a continuous sinusoidal phase of a star connected 3-phase ASM with line voltage 220 V and frequency 50 Hz are given as follows, ignoring core (iron) losses: R1=0.21 Ohm, R2=-0.18 Ohm, X1=X2-0.66 Ohm and Xm = 9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly? Answer options group 8.0815 2.6455 4.3763 7.1534 1.2558 6.3414 5.2280 3.7473
Calculate the impedance ZL for the maximum average power transfer in the circuit shown in Figure 3.and ZLFind the value of the maximum average power transferred to?
A 20 Ohm resistor is in series with a 30 Ohm Inductive reactance. If they are connected to a 40 Volt a.c. source, what is the phase angle between the voltage across the Inductive reactance, and the supply voltage (in degrees)? **Only give the magnitude. If you believe the current is lagging OR leading, give a positive value for the angle " I
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ??.and ??Find the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
For maximum average power transfer in the circuit shown in the figure, set the impedance ZLand ZLFind the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
The per unit impedance of a generator on a 60 MVA, 20 kV base is j0.09 p.u. The per unit impedance to a 100 MVA, 20 kV base will be (a.) j0.054 p.u. (c.) j 1.5 p.u. (b.) j0.54 p.u. (d.) j0.15 p.u.