A regular rod is 3 meters long and weighs 100 Newtons,with ends A and B resting on two supports andcarrying a weight of 50 Newtons at a distance of o.5meters from the A end and the weight is 150 Newtonsat a distance of 2 meters from the first gravity. Find thereaction forces at both A and B.W1ABW22-3 JS3.

To find support reaction at A and B

regular rod is 3 meters long and weighs 100 Newtons, with ends A and B resting on two supports and carrying a weight of 50 Newtons at a distance of o.5 heters from the A end and the weight is 150 Newtons a distance of 2 meters from the first gravity. Find the reaction forces at both A and B. W1 A B W2 2-3 JSi

regular rod is 3 meters long and weighs 100 Newtons, with ends A and B resting on two supports and carrying a weight of 50 Newtons at a distance of o.5 heters from the A end and the weight is 150 Newtons a distance of 2 meters from the first gravity. Find the reaction forces at both A and B. W1 A B W2 2-3 JSi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The control linkage for a machine consists of two L2 steel rods BE and FG, each rod has a diameter of 0.96 in. If a device at G causes the end G to freeze up and become pin connected, determine the maximum horizontal force, P, that could be applied to the handle without causing either of the two rods to buckle. The members are pin connected at A, B, D, E, and F.
The truss shown in figure below is supported by a hinge at A and a roller at B. A load of 2000 kN is applied at C. Determine the reactions at A and B. 30 2000 10 5 RAE TRB- -30- -10- RA RAv
Quizs- Replace the loading system by an equial ent resultant force and Couple moment acting at Point o. fi=l00 N Mc:75 Nm 0:3m 200 0-5 m 0.4m
Analyze the bearm shown below if the loads are as follows: P- 168 kN w - 28 kN/m M = 152 kN.m a. Which of the following most nearly gives the reaction at the roller support in kN [ Select ) b. Which of the following most nearly gives the reaction at the hinge support in kN [ Select] M 30 -2 m--2 m 4 m 3 m w/
A 8K 4K 16'-0" 1.5 K 4'-0" 4'-0" 4'-0" 4'-0" 2a. Support A is fixed. Calculate the reactions at support A. Show the reactions clearly on the diagram.
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the deformation at wire BD. E 4 m +2m+2m -3 m O 0.417mm O 0.497mm O 0.329mm O 0.231mm
For the beams shown in Figures P4-21 ments and slopes, the forces in each element, and the reactions. -4 m ■Figure P4-21 2 KHE 4 kN/m 4 m determine the nodal displace- 3 E = 70 GPa 1 = 3 x 10-4 m²
EQUILIBRIUM Smooth- bearing 5 1000⁰ 12' P4-121 PMEGSYS Boll and socket! CHAP. 4 1. 4-121. The homogeneous block of Fig. P4-121 has a specific weight of 50 lb per cu ft. The 2000-lb force acting at B is parallel to the x axis, while the bearing at F is in a plane parallel to the xy plane. Determine the components of the reaction of the bearing on the rod at F. I 2000lb B -Boll
Aen = a0 © @2 Z Q23-7-2018p.. Q1: A railway ridge consisting of truss construction as shown in the Figure below, this truss is supported by A and B. The forces on joints il and V are i the uss result from a i crossing the railway bridge Determine the following: (a)the reactions forces in A and B (b)the forces of the truss members in joints (1.1, I and 1V) >
Problem 7: The bar AB is supported by two smooth collars. At A the connection is with a ball- and-socket joint and at B it is a rigid attachment. If a 50 – lb load is applied to the bar, determine the x, y, z components of reaction at A and B. ,у, B 6 ft 6 ft 4 ft 50 Ib 5 ft 3 ft
F5-1. Determine the horizontal and vertical components of reaction at the supports. Neglect the thickness of the beam. 500 Ib 600 Ib - ft B Esa sato -5 ft- -5 t- -5 ft-
An 8m bar hinged at the left end carries a 100N load 5m from the hinge support. The bar is also supported by two springs- one at the midspan (steel, G= 80 GPa)and the other at the right end (bronze, G=50 GPa). The springs both has a mean diameter of 100 mm and is made of 10-mm wire. The steel spring consists of 10 turns while the bronze spring consists of 8. Assume bar is rigid. Determine the maximum shearing stress for each of the spring. Assume springs are light springs.